background image

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST 

 

DD3691471  072017 

201 Daktronics Drive  PO Box 5128  Brookings, SD 57006-5128 

 

800-325-8766  605-692-0200  fax 605-697-4700 

www.daktronics.com  email [email protected] 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Diving Judge 

Controls 

 

 

 

 

 

 

 

 

Using standard Ethernet cable, connect from Hy-Tek computer to the 

ETHERNET jack on the back of the OmniSport. 

 

MENU > 4 > 7 > 7 NETWORK MMR: ON 

 

Ensure that the IP address is within range of the OmniSport IP, and 

the Subnet and Gateway match. 

o

 

Open Hy-Tek software to configure settings. Start by entering the Run screen 

from the top header. 

 

Interfaces > Setup > Timing Console Interface > Daktronics 

OmniSport 2000 (Serial or UDP). 

 

Interfaces > Setup > Scoreboard > Daktronics (Serial or UDP). 

***Alpha Scoreboard Interface needed for matrix RTD.

 

o

 

Some setups use Generic Serial for Alternative 

configurations (CTS Timer). 

 

 

o

 

Verify judge console firmware is up to date (3.0 or higher). JC-100 and  

RC-100 options. 

o

 

Verify base station firmware is up to date if using wireless judge consoles  

(3.0 or higher). 

o

 

Verify the base station function. Function setting should be set to a 6 on 

version 3.0 and higher. (Function 1 for earlier versions). 

o

 

Verify the correct 900 MHz antenna is being used on the base station. 

o

 

Verify the judge consoles are communicating to the OmniSport 2000.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Detailed Instructions: ED-13312 (Section 7)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pace Clocks 

 

 

 

 

 

 

 

 

 

 

 

o

 

Visually inspect space clock (switches, knobs, and connections). 

o

 

Verify pace clock firmware is up to date. 

o

 

Verify pace clock operation. 

 

 

After completing the checklist:  

    Still having issues? 

o

 

Search ou

Knowledge Base

 for additional  

troubleshooting resources.

 

o

 

Create a new service case in your 

MySupport Account

 

PC-2001 Manual: ED-13737

 

PC-2002 Manual: ED-14253 

TI-2022 Manual: ED-13736 

 

Содержание Aquatics







Отзывы: