Dakota Digital VHX-78C-MC Скачать руководство пользователя | Manualshive

Страница: 8 / 42

background image

650374

8. If the instrument housing was removed from the dashboard, reinstall, then attach the bezel to the housing
with the seven factory screws removed in Step One. Refer to the main manual for wiring instructions to
complete the VHX installation.

4510 W. 61

st

St. N., Sioux Falls SD 57107

Phone: (605) 332-6513 Fax: (605) 339-4106

www.dakotadigital.com

[email protected]

7. Separate the stock lens from the blackout plate; the original lens is not needed. Place the blackout plate
over the Dakota Digital gauges while aligning the mounting holes. Attach the VHX system using the five
factory screws. Place the included 1/8” white plastic spacer beneath the blackout plate at the lower-most
mounting hole before installing the screw (white arrow).

«
...
6
7
8
9
10
...
»

Содержание VHX-78C-MC











































Отзывы:

Нет отзывов

Похожие инструкции для VHX-78C-MC

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 36

Бренд: palintest Страницы: 14

Professional Plus

Бренд: YSI Страницы: 28

Бренд: Magnet-physik Страницы: 32

Бренд: Flowmetrics Страницы: 102

DIRIS Digiware D-40

Бренд: socomec Страницы: 58

Бренд: Raytech Страницы: 7

Бренд: PASCO Страницы: 4

DELMHORST J-2000

Бренд: ABQ Industrial Страницы: 4

Бренд: General Страницы: 12

Бренд: Velleman Страницы: 32

Бренд: LAUMAS Страницы: 12

Бренд: Roland Страницы: 32

Бренд: LaserLiner Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды