Dakota Digital VHX-78C-MC Скачать руководство пользователя | Manualshive

Страница: 7 / 42

background image

650374

6. With the modifications complete, plug the CAT5 cable in to the display, and feed the cable

through the opening on the right-hand side of the housing. Place the Dakota Digital gauge
cluster into the dash, taking care to align the mounting holes with those in the stock dash.
Remove the protective tape from the lens

4. You should be left with a bare housing. Remove all light bulbs and electrical contacts, as they

are not needed for the VHX system.

5. Using a die grinder, Dremel tool, or cut-off wheel, carefully trim the plastic bosses as shown.

This is necessary to mount the new gauge system.

«
...
5
6
7
8
9
...
»

Содержание VHX-78C-MC











































Отзывы:

Нет отзывов

Похожие инструкции для VHX-78C-MC

Бренд: Panasonic Страницы: 72

KW9M Eco-Power Meter

Бренд: Panasonic Страницы: 2

Бренд: Omega Engineering Страницы: 22

Бренд: Keithley Страницы: 55

Бренд: SAGEMCOM Страницы: 33

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 60

GranTouch Digital Grand Piano

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 47

Professional Plus

Бренд: YSI Страницы: 28

Бренд: Hilti Страницы: 146

Бренд: Sper scientific Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды