background image

REMOTE SYSTEM TRANSMITTER LOCK FUNCTION 

Due to the long range of this system, some customers may wish to avoid accidentally pressing a button 

and opening a door when they are out of sight of the vehicle.  Turning Switch #3 on will enable a transmitter lock 
function.  Pressing buttons 1 and 3 at the same time will lock the receiver from activating any of the outputs.  It 
will remain locked until buttons 1 and 3 are pressed again. 

When DIP switch #3 is off, this feature is disabled. 
To lock the system: 

1. 

Press and release buttons 1 and 3 at the same time. 

2. 

Press one of the other buttons to verify that the system is locked. 

To unlock the system: 

1. 

Press and release buttons 1 and 3 at the same time. 

2. 

Press one of the other buttons to verify that the system is operating normally. 

 

PROGRAMMING SWITCHES 

There are four programming switches located next to the main harness connector.  They are used to set 

up the operation of the remote system. 
Switch #1 

Select operation mode.  (changes what button 5 does) 

Switch #2 

Select auxiliary output type.  (momentary on or latch on/latch off) 

Switch #3 

Enable or disable transmitter lock function. 

Switch #4 

Enter testing and programming mode. 

 

BATTERY REPLACEMENT 

  

Should the transmitter function become weak or erratic, the battery in the key chain transmitter may be 

weak.  An indication of a weak battery is that the green indicator may have a dim glow to it when any button is 
pressed.  The battery is replaced in the following manner: 
1. 

Remove the small screw on the back of the transmitter case. 

2. 

Carefully separate the two case halves. 

3. 

Remove the battery, noting the (+) and (-) position. 

4. 

Replace the battery with a new 12 volt type GP23A battery which is available at most electronic stores 
(Radio Shack, battery stores, etc.). 

5. 

Carefully replace the top cover and refasten the screw 

 

INSTRUCTIONS FOR TESTING AND PROGRAMMING TRANSMITTERS 

All of the transmitters to be programmed into the system should be available.  This sequence will erase 

any previously programmed transmitters.  If a transmitter is lost or stolen, go through the programming sequence 
with the remaining transmitters and the lost one will be erased.  The programming light is located next to the four 
programming switches. 
Placing receiver into programming/testing mode. 
1. 

Unplug the main harness connector from the receiver unit. 

2. 

Turn Switch #4 on. 

3. 

Plug in the main harness connector so that the unit has power.  The red programming light should come 
on and remain on. 

Testing the transmitters. 
1. 

Press button 5.  The programming light should flash as long as the button is held. 

2. 

Press button 1.  The programming light will flash if the transmitter is currently programmed in.  This will 
also resyncronize the transmitter with the decoder.  The number of flashes will indicate the transmitter 
number. 

Programming the transmitters. 
1. 

Turn Switch #4 off.  The programming light should go off.   
(If no transmitter buttons are pressed within 6 seconds the system will exit the programming routine.) 

2. 

Press and release button number 3.  The programming light should come on. 

3. 

Press and release button number 3 again.  The programming light should flash and then go out.  It will 
flash once for the first transmitter, twice for the second, etc. 

4. 

The transmitter is now stored.  If you have more transmitters, take the next transmitter and go back to 
step 2. 

5. 

Press button 4.  This will exit the programming mode and restart the system. 

 

11 

Содержание CMD-9000













Отзывы: