background image

OPERATION AS AUTO HEIGHT CONTROL SYSTEM 

 
The auto height control system is active when both the large red power wire and the accessory 
power wire are on.  When the accessory power is off the display and height control will shut 
down to prevent draining the battery down.  One exception is that if the bag dump is active and 
the ignition is turned off, the control system will continue to operate until the bag dump is 
completed and will then shut down. 
The display unit has a 2 line, full character display with three switches on each side.  The 
display unit communicates to the control system through two wires.  The center left switch 
selects the different functions and toggles the display screens.  The center right switch acts as 
the manual up/down selector.  The four corner switches operate the four corner bags in manual 
or programming modes and also operate as menu selection in other modes.  Each of the 
operating modes will be discussed in detail. 

Manual control: 

The tank pressure area will display “AIR” if a tank pressure sender is not connected.  Pressing 
the up/down select switch will change the operation of the four corner switches.  When 
“MANUAL UP” is displayed the corner switches will raise their respective bags for as long as the 
button is held. When “MANUAL DOWN” is displayed the corner switches will lower the bags.  
More than one switch can be held at a time. 

UP/DOWN CONTROL INDICATION

RIGHT FRONT CONTROL

RIGHT REAR CONTROL

MANUAL SELECT

RIGHT REAR PSI

LEFT REAR PSI

AIR  85 F  84 MANUAL

PSI  72 R  73  DOWN 

LEFT FRONT PSI

TANK PSI

LEFT REAR CONTROL

LEFT FRONT CONTROL

MODE SELECT

RIGHT FRONT PSI

 

 

Auto control: 

The tank pressure area will display “AIR” if a tank pressure sender is not connected.  Pressing 
the manual select button will switch to manual mode.  To change to a different auto height 
control mode, press the mode select button once and then use the corner switches to select the 
desired mode as shown on the display screen. 

AUTO MODE INDICATION

NO FUNCTION

NO FUNCTION

MANUAL SELECT

RIGHT REAR PSI

LEFT REAR PSI

LEFT FRONT PSI

135 120 F 120  AUTO 
PSI 120 R 120 NORMAL

TANK PSI

NO FUNCTION

NO FUNCTION

MODE SELECT

RIGHT FRONT PSI

 

 

 

6

Содержание ARC-1000












Отзывы: