background image

Worn bumper

Replace bumper, check driver and driver piston 
O-ring

Driver channel worn

Fasteners jam in tool

Replace fixed nose

Wrong sized fastener

Use only recommended fasteners

Bent/damaged fasteners or collation

Discontinue using these fasteners

Loose magazine/nose screws

Tighten all screws

Broken/chipped driver

Replace driver

Fasteners misses metal 
connector hole

Damaged moveable nose

Replace moveable nose

Nail not fully positioned in the drive 
channel

Check for debris/collation in drive channel; remove 
debris/remove nails and replace with new strip

Hole not properly located with point of 
nail

Place nail point in metal connector hole before firing 
the tool

Nail point not visible

Trigger stem depressed

Release trigger; disconnect and reconnect air; replace 
trigger valve assembly

Nose spring broken

Replace nose spring

Nail jammed in drive channel

Disconnect air/clear jam

Less than 5 nails/tool in lockout mode

Disconnect from air and add new strip of nails

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

SYMPTOM

Dirt/grime in driver channel

Disassemble and clean driver and sleeve

Skipping fasteners;
intermittent feed

Содержание HSPW38













Отзывы: