DaimlerChrysler LH New Yorker 1994, Электронное руководство по обслуживанию

Страница: 296 / 1203

CENTER UPPER OUTLET BEZEL REMOVAL
(1) Pull center bezel rearward and disengage the
two retaining clips and disconnect electrical connector
(Figs. 24 and 25).
(2) May require a hook tool to pry-out right end of
bezel.
(3) For installation, reverse above procedures.
LOWER CENTER BEZEL REMOVAL
(1) Pull bezel straight rearward along the sides of
the radio and A/C control openings to disengage (6)
clips (Fig. 22).
(2) For installation, reverse above procedures.
LEFT UNDER INSTRUMENT PANEL
SILENCER/DUCT REMOVAL
(1) Remove push-in fastener under left end of in-
strument panel (Figs. 24 and 25).
(2) Maneuver part off of brake bracket stud and
center floor distribution duct to remove.
(3) For installation, reverse above procedures.
RIGHT UNDER INSTRUMENT PANEL
SILENCER/DUCT REMOVAL
(1) Remove two push-in fasteners at center and left
end of silencer/duct (Figs. 24 and 25).
(2) Maneuver part off of center floor distribution
duct to remove.
(3) For installation, reverse above procedures. Re-
install prior to knee bolster.
WOOD GRAIN TRIM BEZEL REMOVAL—NEW
YORKER
(1) Open right front door and remove right end
cover and center upper outlet bezel (Fig. 25).
(2) Remove screw at right end of instrument panel
and screw at center outlet opening.
(3) Remove wood grain bezel by pulling straight
rearward, disengaging the three clips.
(4) For installation, reverse above procedures.
RADIO REMOVAL
(1) Remove lower center bezel and remove two ra-
dio retaining screws and then remove radio (Fig. 22).
(2) Pull radio straight out and disconnect both elec-
trical connectors, antenna cable and remove screw on
radio ground strap, then remove radio.
(3) For installation, reverse above procedures.
ASH RECEIVER/LAMP REMOVAL
(1) Remove lower slide out ash tray (Fig. 24).
(2) Remove two outboard screws from carrier as-
sembly.
(3) Remove carrier and pull rearward to disengage
from the forward locator.
(4) Ash receiver light is accessible by removing
socket from metal light housing and remove lamp
from socket.
(5) For installation, reverse above procedures.
CIGAR LIGHTER REMOVAL
(1) Remove lower slide out ash tray (Fig. 22).
(2) Remove two outboard screws from housing as-
sembly.
(3) Remove housing and pull rearward to disengage
from the forward locator.
(4) Ash receiver light is accessible by removing
socket from metal light housing and remove lamp
from socket.
(5) Disconnect the two cigar lighter wiring connec-
tors from cigar lighter. Unscrew shell and clamp as-
sembly to replace cigar lighter assembly.
(6) For installation, reverse above procedures. The
shell has a location feature.
ASH RECEIVER/LAMP REMOVAL—NEW YORKER
(1) Remove ash tray and lower center bezel (Fig.
22).
(2) Remove two housing mounting screws.
(3) Remove the housing and lamp.
(4) For installation, reverse above procedures.
CIGAR LIGHTER REMOVAL—NEW YORKER
(1) Remove ash tray and lower bezel (Fig. 22).
(2) Remove two housing mounting screws. Remove
the housing and lamp.
(3) Remove two A/C-Heater control mounting
screws. Move to the A/C-Heater control.
(4) Reach through the A/C-Heater control opening
to disconnect the two wire from the cigar lighter
wiring connectors. The cigar lighter shell can be un-
screw from the clamp so that the cigar lighter can be
removed.
(5) For installation, reverse above procedures.
GLOVE BOX DOOR/HANDLE REMOVAL
(1) Remove three screws at bottom of glove box
door, open glove box door and press sidewalls inboard
to remove door from panel (Figs. 24 and 25).
(2) Position the glove box on cloth to protect paint.
Remove nine screws from backside of the door, New
Yorker has eight screws. Then separate the inner and
outer door. Handle and latch can be removed at this
time.
GLOVE BOX LIGHT/SWITCH REMOVAL
(1) Open glove box door and pull out glove box light
switch from upper right corner of glove box opening
on instrument panel (Figs. 24 and 25).
(2) Replace lamp or remove electrical connector to
replace switch.
(3) For installation, reverse above procedures.
TRUNK RELEASE SWITCH REMOVAL
(1) Open glove box door and pry switch out of open-
ing (Figs. 24 and 25).
INSTRUMENT PANEL AND GAUGES 8E - 11