Daikin VRV III RXYQ-PY1K, Руководство по установке, Страница: 22 / 34

Installation manual
19
RXYQ8~1 RXYQ8~12P7YLK
VRVIII System air conditioner
4PW41760-1
1 Adding refrigerant using leak detection function (for
RXYQ_Y1K units only)
The automatic refrigerant charging has limits as described
below.
At out of limit, the system can not operate the automatic
refrigerant charging.
To speed up the proces of charging refrigerant for large systems, it is
recommended to first manually charge a portion of the refrigerant
first before performing automatic charging.
1 Calculate how much refrigerant to be added using the formula
explained in the chapter
"How to calculate the additional
refrigerant to be charged" on page 9 .
2 The amount of pre-charging is 10 kg less than the calculated
amount.
3 Open valve C (valves A and B and the stop valves must be left
closed) and charge the refrigerant in liquid form via the liquid
side stop valve service port.
(See figure 29)
4 If the calculated amount of pre-charging is reached, close
valve C.
5 After pre-charging, perform the refrigerant charge operation as
shown below and charge the remaining refrigerant of the
additional charging amount through valve A.
(See figure 30)
1. Start of automatic charging refrigerant
-
Open the liquid and gas side stop valves and the service port
stop valve. (Valves A, B and C must be closed.)
- Close all frontpanels except the electric box frontpanel and
turn the power ON.
- Make sure all indoor units are connected, refer to "11.3. How
to check how many units are connected" on page 17 .
- If the H2P LED is not flashing (in 12 minutes time after
turning on the power), make sure it is displayed as shown in
the
"3 Normal system display" on page 22 .
If the H2P LED is flashing, check the malfunction code on the
remote controller
"4 Remote controller malfunction code
display" on page 22 .
2. Press the button once if the LEDs combination is not
as in the figure below.
3. Press the button once.
4. Hold the button down for 5 seconds or more.
5. Charging mode judgement
For automatic charging, the charging must be done in cooling
mode.
However, if the indoor temperature is 10°C DB or lower, in some
cases the unit will first charge in heating mode to increase the
indoor temperature.
The unit will automatically select the cooling mode or heating
mode for charging.
Outdoor temperature : 0°C DB~43°C DB
Indoor temperature : 10°C DB~32°C DB
Total indoor unit capacity :
≥
80%
1 Measuring instrument
2 Tank (siphon system)
3 Charge hose
4 Liquid line stop valve
5 Gas line stop valve
6 Stop valve service port
7 Valve B
8 Valve C
9 Valve A
10 Outdoor unit
11 Refrigerant charge port
12 To indoor unit
13 Interunit piping
14 Refrigerant flow
At least the unit should be charged with its original amount
of refrigerant (refer to the nameplate on the unit), before
starting the automatic charging.
1 Measuring instrument
2 Tank (siphon system)
3 Charge hose
4 Liquid line stop valve
5 Gas line stop valve
6 Stop valve service port
7 Valve B
8 Valve C
9 Valve A
10 Outdoor unit
11 Refrigerant charge port
12 Field piping
13 Refrigerant flow
14 Indoor unit
NOTE
For a multi outdoor unit system, it is not required
to connect all charge ports to a refrigerant tank.
The refrigerant will be charged with ±22 kg in
1 hour time at an outdoor temperature of 30°C DB
or with ±6
kg at an outdoor temperature of
0°C DB.
If you need to speed up in case of a multiple
outdoor system, connect the refrigerant tanks to
each outdoor unit as shown in
figure 30 .
H1P H2P H3P H4P H5P H6P H7P
x x w x x x x
H1P H2P H3P H4P H5P H6P H7P
w w w w w w w
During charging in heating mode, a person must
manually close valve A before complete charging is
finished. The required amount is the the calculated
amount (see
"6.6. Example of connection" on page 8 )
minus 10 kg, therefore, the weight must be monitored
constantly.
BS1 MODE
BS4 TEST
BS4 TEST