manualshive.com logo in svg

Daikin VRV II-Q RQYQ8-48PY1B, Руководство по обслуживанию

Поделиться
Скачать
Daikin VRV II-Q RQYQ8-48PY1B Скачать руководство пользователя страница 172

Troubleshooting by Remote Controller

SiBE341027

162

Service Diagnosis

Troubleshooting

NO

NO

YES

YES

NO

YES

YES

Connect the power supply wire 
for the external control adaptor 
for outdoor unit to 5V supply 
line.

Replace the outdoor unit main 
PCB.

Check if the power supply 

wire for the external control 

adaptor for outdoor unit is 

connected to 5V supply 

line.

Replace the PCB of the external 
control adaptor for outdoor unit.

Replace the outdoor unit main 
PCB.

NO

YES

NO

Correct the connecting wiring 
with the external control adaptor 
for outdoor unit.

Diagnosis Flow 1

Supply the power to the outdoor 
unit.

Check if power is 

supplied to the outdoor 

units.

Check if the normal 

condition monitor LED for 

the outdoor unit PCB 

blinks.

Check if the normal 

condition monitor LED 

for the external control 

adaptor for outdoor 

unit blinks.

Confirmation of error 3 Confirmation of error 4

Check if any disconnection or 

connection error is detected 

in connecting wires with 

external control adaptor for 

outdoor unit.

Caution

Be sure to turn off power switch before connect or disconnect connector, 
or parts damage may be occurred.

Содержание VRV II-Q RQYQ8-48PY1B






















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды