Daikin SkyAir RZQ-P Series Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 238

background image

EDUS281120_a

Installation of indoor unit

RZR-P, RZQ-P(9)

141

3PN06240-12Q

5

English

12 or more

Air inlet

Air outlet

Obstruction

Floor

Required service
space

(Length : in.)

1 3/16 or more

1 3/16 or more

∗

∗

Where pipe between indoor and outdoor units is possible

•

within the allowable limit.
(Refer to the installation manual for the outdoor unit.)
Install the indoor and outdoor units, power wire and

•

connecting wires at least 3.5 ft. away from televisions or
radios in order to prevent image interference or noise.
(Depending on the radio waves, a distance of 3.5 ft. may
not be sufﬁ cient enough to eliminate the noise.)

Use suspension bolts for installation. Check whether

(2)

the ceiling is strong enough to support the weight of
the unit or not. If there is a risk, reinforce the ceiling
before installing the unit.

(Installation pitch is marked on the paper pattern for instal-
lation. Refer to it to check for points requiring reinforcing.)

This product may be installed on ceilings up to 10.6 ft.

(3)

from the ﬂ oor.

A direction of installation.

(4)

Refrigerant piping : the rear side, right side or upper part.

•

Wiring : only the rear side.

•

Drain piping : the rear right side or the right side.

•

(As the rear left, installation is impossible.)

PREPARATIONS BEFORE INSTALLATION

4.

Relation of holes for indoor unit, suspension bolt posi-

(1)

tion, piping and wiring.

3 3/4

6 1/4

26 1/8

Conduit
hole

Front view

62 5/8 (Indoor unit)

61 (Suspension bolt pitch)

7 1/4

6 1/4

8 1/4

10 1/4

(Suspension

bolt pitch)

26 3/4 (Indoor unit)

27 3/16

24 5/8

Top liquid pipe hole

Top gas pipe hole

Suspension bolt (× 4)

Air outlet

False ceiling view

(length : in.)

Wiring hole

Drain pipe hole

Rear side pipe hole

22

25 3/4
27 11/16

5 5/8

6

Make holes for suspension bolts, refrigerant and drain

(2)

pipe, and wire.

Refer to the paper pattern for installation.

•

Select the location for each of holes and open the holes in

•

the ceiling.

Remove the parts from the indoor unit.

(3)

Detach the suction grille.

(3-1)

Slide the locking knobs (×2) on the suction grille inward

•

(direction of arrows) and lift upwards.

(Refer to Fig. 1)

With the suction grille open, remove the suction grille for-

•

ward, holding on to the rear tabs (×2) on the suction grille.

(Refer to Fig. 2)

Fig. 1

Knob

Suction grille

Fig. 2

Suction grille

Tab

Remove the decoration panels (left and right) and the pro-

(3-2)

tection net.

After removing the securing screws for the decoration

•

panels (one each), pull them forward (in the direction of
the arrow) and remove them.

(Refer to Fig. 3)

Remove the securing screws for the protection net.

•

(Refer to Fig. 3)

Decoration panel
securing screw
(M4)

Decoration panel

Fig. 3

Protection net
securing screws (M4)

Decoration
panel

Decoration panel
securing screws (M4)

Raise one side of the protection net upwards (in the direc-

•

tion of the arrow (i)) and remove back (the arrow (ii)).

(Refer to Fig. 4, 5)

Take out the accessories.

•

Decoration panel

Decoration
panel

Accessories

Fig. 4

Protection net

(ii)

(i)

«
...
140
141
142
143
144
...
»

Содержание SkyAir RZQ-P Series















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SkyAir RZQ-P Series

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 118

Бренд: Samsung Страницы: 16

Бренд: Argo Страницы: 38

Бренд: Hyundai Страницы: 52

Бренд: Daikin Страницы: 11

Бренд: Argo Страницы: 92

Бренд: PremierOne Страницы: 7

Бренд: MrCool Страницы: 27

Air Purifier 60

Бренд: Airfree Страницы: 24

Бренд: Airrex Страницы: 16

Бренд: Magnum Industrial Страницы: 6

TA36FFLL-1232IA

Бренд: Tesla Страницы: 288

Бренд: Bryant Страницы: 56

Бренд: Jata Страницы: 16

Бренд: Jata Страницы: 16

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды