background image

Downward

inclination of 

1/100 or more

1~1.5 m

Support

Good

Wrong

Fig. 14

 CAUTION

If drain stagnates in the drain piping, the piping may be 
clogged.

• 

If sufficient downward inclination cannot be ensured, 

carry out upward drain piping.

• 

Install supports at a distance of 1 to 1.5 m so that the pip-

ing may not deflect. 

(Refer to Fig. 14)

• 

Make sure to use the attached drain hose (1) and the 
metal clamp (2). 
Insert the drain hose (1) into the drain socket up to the 
point where the socket diameter becomes larger.  

  Put the metal clamp (2) to the taped hose end and 

tighten the metal clamp (2) with torque 1.35±0.15 N·m 

(135±15 N·cm).

Metal clamp (2)

(accessory)

Drain socket

Tape

VP20 side VP25 side

Hose end

Drain hose (1)

(accessory)

Fig. 15

 CAUTION

• 

Do not tighten the metal clamp (2) with the torque more 

than the specified value.

 

The drain hose (1), the socket or the metal clamp (2) may 
be damaged.

• 

Wrap the vinyl tape around the end of the metal clamp 
(2) so that the sealing material (Large) (10) to be used at 
the next process may not be damaged with the clamp 
end or bend the tip of the metal clamp (2) inward as 
shown. 

(Refer to Fig. 16)

<In case of sticking vinyl tape>

Tightened part

appro

x.

 90°

Stick vinyl tape without 

tearing the sealing 

material (Large) (10) .

Vinyl tape

<In case of bending the tip>

Bend the tip without tearing the 
sealing material (Large) (10).

Tightened part

appro

x.

 90°

Fig. 16

< Caution to be taken when carrying out upward drain 

piping (Refer to Fig. 17) >

• 

The maximum height of the drain riser is 675 mm. Since 
the drain pump mounted on this indoor unit is a high 
head type, from the characteristic point of view, the 
higher the drain riser the lower the draining noise. 
Therefore, the drain riser of 300 mm or higher is recom-
mended.

• 

For upward drain piping, keep the horizontal piping dis-
tance of 300 mm or less between the drain socket root 
to the drain riser.

Ceiling slab

300 or less

1~1.5 m

Support

Metal clamp (2) (accessory)

Drain hose (1) (accessory)

Upward drain piping

Drain riser

Adjustable

(675 or less)

(850 or less)

Drain hose (1) 

(accessory)

Level or upward 

inclination

Keep the drain hose level or make a slight up-grade so 

that air may not stagnate in the drain hose.

If air stagnates, the drain may flow oppositely when 

the drain pump stops and generate abnormal sound.   

(unit  [mm])

Fig. 17

3P335596-2D        English

Содержание FXFQ25SVM





















Отзывы: