background image

English

13

When extending the drain hose, use a commercially available drain extension hose, and be sure to 
insulate the extended section of the drain hose which is indoors. 

(Refer to Fig. 17)

Make sure the diameter of the piping is the same as the piping (hard vinyl chloride, nominal diameter 
13mm) or bigger.

When directly connecting a hard vinyl chloride pipe joint (nominal diameter 13mm) to the drain hose 
connected to the indoor unit (i.e. for embedded piping, etc.), use a commercially available hard vinyl 
chloride pipe joint (nominal diameter 13mm). 

(Refer to Fig. 18)

(2) Make sure the drain works properly.

After drain work is complete, perform a 

drain check by opening the front panel, 

removing the air filter

, pouring water 

into the drain pan, and making sure 

water flows smoothly out of the drain 

hose.

 (Refer to Fig. 19)

CAUTION

Drain piping connections
Do not connect the drain piping directly to sewage pipes that smell of ammonia. The ammonia in the 
sewage might enter the indoor unit through the drain pipes and corrode the heat exchanger.

Keep in mind that it will become the cause of getting drain pipe blocked if water collects on drain pipe.

7. ELECTRIC WIRING WORK

7-1 GENERAL INSTRUCTIONS

All field supplied parts and materials and electric works must conform to local codes.

Use copper wire only.

For electric wiring work, refer to also “WIRING DIAGRAM” attached to the unit body.

For remote controller wiring details, refer to the installation manual attached to the remote controller.

All wiring must be performed by an authorized electrician.

This system consists of multiple indoor units. Mark each indoor unit as unit A, unit B..., and be sure the 

terminal board wiring to the outdoor unit and BS unit are properly matched. If wiring and piping between the 

outdoor unit and an indoor unit are mismatched, the system may cause a malfunction.

Indoor unit drain hose

Extension drain piping 
(commercially available)

Insulating tube 
(commercially available)

Insulating tape (accessory) (4)

( See “4.INDOOR UNIT INSTALLATION” )

Fig. 17

Drain hose connected 
to the indoor unit

Commercially available 
hard vinyl chloride pipe 
joint (nominal diameter 13mm)

Commercially available 
hard vinyl chloride pipe 
(nominal diameter 13mm)

Fig. 18

Plastic container 
for pouring

Drain pan

Fig. 19

Make sure not to splash the water.

4PEN494115-1A.book  Page 13  Tuesday, October 3, 2017  10:51 AM

Содержание FXAQ15AUV1B





























Отзывы: