Daikin FTYN25DV3B ATY20DV2 Скачать руководство пользователя страница 81

Страница: 81 / 128

Indoor Unit

SiBE01-503

Removal Procedure

1. Indoor Unit

1.1

Removal of

Air Filter

Procedure

Warning

Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.

Step

Procedure

Points

1. External features

If ON/OFF button is kept
pushing for 5 seconds, a
forced cooling operation will
be carried out for approx. 15
minutes.

When the

signal receiver

catches a signal from the
remote controller, it
produces beep sound and
the operation lamp blinks.

2. Remove the air filters.

Pull protrusions on left
and right sides of panel
with fingers and open
front grille all the way.

Lift center section of air
filter and disengage
hooks.
Remove air filter by
pulling forward.

Left and right filters are
interchangeable.

To re-install, insert air filter
along the guide.

Содержание FTYN25DV3B ATY20DV2

































































































































Результаты поиска

Содержание FTYN25DV3B ATY20DV2

Отзывы:

Daikin FTYN25DV3B ATY20DV2, Руководство по обслуживанию, Страница: 81 / 128

Результаты поиска

Содержание FTYN25DV3B ATY20DV2

Отзывы: