Daikin FTKD50BVM Скачать руководство пользователя страница 130

Страница: 130 / 210

Si04-306

Troubleshooting

Service Diagnosis

121

Troubleshooting

Check No.4

Refer to P.126

Check No.6

Refer to P.128

Reconnect in position.

Open the stop valve.

Repair the pipe flare or
replace the square union.

Check the power transistor
harness for looseness.
Correct it as required. Also
replace cracked pipe if any.

Check the pipes for
improper contact. Correct
as required. Also replace
cracked pipe if any.

Replace the electronic
expansion valve.

CT in trouble (refer to H8).

Replace the room
temperature or outdoor air
thermistor, or the indoor
unit or outdoor unit heat
exchanger thermistor.

(1) Replace the PCB.
(2) Replace the compressor.

Procedure complete

(R2853)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Any thermistor

disconnected?

YES

Malfunctioning

Functioning

Stop valve closed?

YES

Check the CT.

YES

Gas shortage error again?

Functioning

Check No. 6

Check the thermistors.

YES

Oil oozing at internal piping?

YES

Check No. 4

Electronic expansion valve

functioning?

YES

Oil oozing at relay pipe

connections?

Check for gas leakage.

Change for a specified amount of
fresh refrigerant.

YES

Compressor vibrating

too much?

* Discharge pipe thermistor
* Indoor / outdoor unit heat exchanger thermistor
* Room temperature thermistor
* Outdoor air thermistor

Содержание FTKD50BVM



















































































































































































































Результаты поиска

Содержание FTKD50BVM

Отзывы:

Бренды по названию

Популярные бренды

Daikin FTKD50BVM, Руководство по обслуживанию

Результаты поиска

Содержание FTKD50BVM

Отзывы:

Бренды по названию

Популярные бренды