Daikin FTKD50BVM Скачать руководство пользователя страница 120

Страница: 120 / 210

Si04-306

Troubleshooting

Service Diagnosis

111

Troubleshooting

Check No.12

Refer to P.132

Turn off the power and turn it on
again.

Check No. 12

Check the capacitor voltage.

Replace the outdoor unit
PCB.

* Inverter checker
Part No.: 1225477

Correct the power supply or
replace the SPM.
(Replace the outdoor unit
PCB.)

Replace the outdoor unit
PCB.

Replace the compressor.

Replace the outdoor unit
PCB.

Check the supply voltage.

(R2848)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

∗

Running current

as shown at right with relay

cable 1 or 2?

YES

Current
(guideline)

2 sec

Time

Rising with increasing
frequency

Capacitor charged when
the indoor unit or outdoor
unit main relay turns on

DC380±30V?

YES

Voltage within

the allowable range (Supply

voltage±15%)?

YES

Any LED off?

Compressor running?

YES

Get the system started.

Measure the rectifier input voltage.

Turn off the power. Disconnect the
harnesses U, V and W.

Check with the inverter checker (

∗

Turn off the power and reconnect
the above harnesses. Then turn on
the power again and get the
system restarted.

Содержание FTKD50BVM



















































































































































































































Результаты поиска

Содержание FTKD50BVM

Отзывы:

Бренды по названию

Популярные бренды

Daikin FTKD50BVM, Руководство по обслуживанию

Результаты поиска

Содержание FTKD50BVM

Отзывы:

Бренды по названию

Популярные бренды