Daikin FC2 Скачать руководство пользователя страница 52

Страница: 52 / 56

Translation from original instructions

Packaged Rooftop

We reserve the right to make changes without any prior notice.

UATYA

4P645202-1

7.4 Periodic checks

Carry out periodic checks to make sure the unit is working correctly:

OPERATION

RECOMMENDED

FREQUENCY

Check the operation of all the control and safety equipment as described previously.

Monthly

Check the tightness of the electrical terminals in the electrical control panel and in the terminal

boards of the compressors. The moving and fixed contacts of the contactors must be cleaned

periodically and should be replaced whenever they show signs of deterioration.

Monthly

Check the refrigerant charge through the liquid sight glass.

Monthly

Make sure there are no oil leaks from the compressor.

Monthly

Make sure there are no water or water/glycol mixture leaks in the hydraulic circuit.

Monthly

If the unit is to remain out of service for a long time, drain the water from the pipes and the

heat exchanger. This operation is necessary if ambient temperatures lower than the freezing

point of the fluid used are expected during the time it is to remain stopped.

Seasonal

Check the filling of the water circuit.

Monthly

Check that the differential water pressure switch, or the flow switch (where present), is working

correctly.

Monthly

Check the crankcase heaters of the compressors.

Monthly

Clean the finned coil by following the instructions in the “External cleaning” section according

to the type of coil installed

3 months

Clean the air filters

Monthly

Clean the ventilation filters of the electrical control panel.

Monthly

Carry out the defrosting test.

Monthly

Check the moisture indicator on the liquid sight glass (green = dry, yellow = wet). If the

indicator is not green, as indicated on the sight glass sticker, replace the filter.

4 months

Check the condition, fixing and balance of the fans.

4 months

Check that the noise emitted by the unit is normal.

4 months

Test performed to check correct operation of the refrigerant leak detection sensor and its safety

chain connected downline

Yearly

Check that the cable glands in the box of the electrical control panel are tightened.

Yearly

This planning refers to an average installation; there could be installations in which it may be

necessary to increase the frequency of some checks.

Current legislation may require considerably longer intervals on periodic checks than the

recommended ones, also in reference to the safety devices installed and to the refrigerant charge

present, without causing the warranty on the unit to be voided.

Содержание FC2
























































Результаты поиска

Содержание FC2

Отзывы:

Похожие инструкции для FC2

Бренды по названию

Популярные бренды

Daikin FC2, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FC2

Отзывы:

Похожие инструкции для FC2

Бренды по названию

Популярные бренды