background image

IM 871-3 

Page 5 of 12

6.  Remove the grilles at the right and left ends of the primary 

discharge section (

Figure 10

). Position Primary Discharge 

Section on top of room cabinet. Through the openings 
provided by the removed grilles, position the mounting 
brackets at each end of the primary discharge section.

7.  Position the short (bottom) mounting bracket channel so 

the tabs on each end catch the underside of the grille tray 
of the cabinet/sleeve (see 

Figure 10

 detail). The long (top) 

bracket channel will sit on top of the turned flanges of the 

Primary Discharge Section. Adjust the bracket position 
and tighten the Phillips head screw on top of the mounting 
bracket to secure the discharge section to the cabinet.

NOTICE

  If an ExtendAire boost fan is installed, it's power cord will pass 

through the primary discharge section and over the mounting 
brackets, and not underneath.

Note:  Be sure the primary discharge section is positioned 

evenly end-to end with the cabinet/wall sleeve and that 
it is aligned squarely with the front edge of the cabinet/
wall sleeve

8.  Reinstall the touchpad controller by plugging in the 

communication cable into the receptacle in the control 
board. Snap the bezel into the control door opening (

Figure 

11

).

Figure 10: Position and tighten screws on mounting brackets to secure primary discharge section to cabinet/wall sleeve

Locate Right and Left Mounting Bracket

Primary Discharge Section

Mounting Bracket Assembly

Mounting Bracket Detail

Figure 11: Reinstall the touchpad communication cable 
and the touchpad bezel

Reinstall the touchpad 
control bezel into the 
control door opening 

Reinstall the touch-
pad communication 
cable to the control 
board

Go to page 6 and continue installation of ExtendAire compo-
nents.

Содержание ExtendAire IM 871-3













Отзывы: