Daikin EHSH04P30A, Руководство по эксплуатации

Страница: 38 / 56

Operating instructions
38
Daikin Altherma EHS(X/H)
Daikin Altherma integrated solar unit
008.1420944 – 05/2014
6 x Parameter settings
6.10 Rotary switch setting: Info
6.11 Exit button: Sonderfunktion
Parameter Description Access Setting range
Min / Max
Factory
setting
Incre-
ment
BE HF
Overview Display of different current operating data (see section 3.4.1). S S - - -
Water Pressure The current water pressure is displayed in bar. S S 0 - 4 bar - 0.1 bar
T-HS The current temperature (TVBH) of the heat generator is displayed in °C. S S 0 - 100 °C - 1 °C
T-HS Setpoint The current Inflow target temperature of the heat generator is displayed in °C (see
section 3.6.4). S S 0 - 90 °C - 0.1 °C
T-Outside The current external temperature is displayed °C. S S -39 to +50°C 0.1 °C
T-DHW The current temperature of the hot water storage tank is displayed in °C. If there is no hot water
function activated, "- - -" is displayed. S S 0 - 100 °C - 0.1 °C
T-DHW Setpoint The current target hot water temperature is displayed °C. If there is no hot water function acti-
vated, "- - -" is displayed. The current set value is here always the maximum value of all rele-
vant demands for this hot water circuit. S S 10 - 70°C - 0.1 °C
T-Return The current return flow temperature of the heat generator is displayed in °C. If there is no rel-
evant sensor connected to the heat generator, "- - -" is displayed. S S 0 - 100 °C - 0.1 °C
Flow Rate The filtered value of the current volume flow in litres per hour is displayed. S S 0 - 5100 l/h - l/h
T-HC The inflow temperature in the direct heating circuit is displayed in °C. S S 0 - 100 °C - 0.1 °C
T-HC Setpoint The set temperature of the flow in the direct heating circuit is displayed in °C. S S 0 - 90 °C - 0.1 °C
Status HS pump The current status of the internal heat circulation pump in the Daikin Altherma EHS(X/H) is dis-
played. S S Off
On - -
Runtime Compres-
sor The running time of the refrigerant compressor is displayed in h. S S - - h
Runtime Pump The running time of the internal heating circulation pump is displayed in h. S S - - h
Mixer Position The current position of the 3UV DHW 3-way switch valve is displayed.
0%: Position A (room heating)
100%: Position B (domestic hot water generation) S S 0 - 100 % - 1 %
Qboh The amount of heat in the additional heat generator for hot water generation is displayed in
kWh. S S - - kWh
Qchhp The amount of heat in the additional heat generator for heating mode is displayed in kWh. S S - - kWh
Qsc The quantity of heat in the heat pump for cooling is displayed in kWh. S S - - kWh
Qch The quantity of heat in the heat pump for heating is displayed in kWh. S S - - kWh
QWP The total amount of heat in the heat pump is displayed in kWh. S S - - kWh
Qdhw The quantity of heat for hot water generation is displayed in kWh. S S - - kWh
HS type The heat generator type Daikin Altherma EHS(X/H) detected is displayed. S S - - -
Sw Nr B1/U1 The software and version of the RoCon B1 operating unit is displayed. S S - - -
Sw Nr Controller The software number and the version of the RoCon BM1 circuit board are displayed. S S - - -
Sw Nr RTX RT The software number and the version of the RTX-AL4 circuit board are displayed. S S - - -
Tab. 6-12 Parameter in rotary switch setting "Info"
Parameter Description Access Setting range
Min / Max
Factory
setting
Incre-
ment
BE HF
Manual Operation The direct heating circuit and the target hot water temperature are controlled according to the
temperature set in this parameter (see section 3.5.1). E E 20 - 80 °C 50 °C 1 °C
FA failure Display of a current heat pump malfunction in the Daikin Altherma EHS(X/H).

If "----" is displayed there is no fault (see chapter 8).
E E - - -
Protocol Display of protocol (error and information messages). Here we display the saved messages of
the Daikin Altherma EHS(X/H) and the connected data bus units with date a code, in each case
as a menu item. By selecting an entry with the rotary switch, all other corresponding information
is displayed concerning the selected fault message:
- Date and time of the message
- Code number (Information for the heating technician)
- Location (device) where the message originated
- Bus identification (device) where the message originated E E - - -
Delete message By setting this parameter to "On" and briefly pressing the rotary switch all the entries of the pro-
tocol, including the faults from connected data bus devices, are deleted. E E Off
On Off -
Timeprog Reset Resets all permanent time programmes to factory setting (see tab. 3-8). E E Off
On Off -
Return This parameter is used only to exit the special level. E E
Tab. 6-13 Parameter in the level "Sonderfunktion"