manualshive.com logo in svg

Daikin EGSQH10S18AA9W, Руководство по обслуживанию

"Daikin EGSQH10S18AA9W" - компактное и эффективное разделительное устройство с функцией охлаждения и обогрева. Установочное руководство доступно бесплатно для загрузки с manualshive.com. Гарантированное качество и удобство использования делают его идеальным выбором для вашего дома или офиса.

Поделиться
Скачать
background image

ESIE13-03

 

| 

Part 2. Troubleshooting

3. Symptom based troubleshooting

13/05/15 

| 

Version 2.0

Page 37

Ground source heat pump

3.  Symptom based troubleshooting

By deeply analysing the system's components and logic, Daikin offers enhanced symptom based troubleshooting. To provide the 
best troubleshooting efficiency, the related root cause categories for each symptom are ranked. The following ranking is used: 
software control functions, end user related, parameter settings, installation related, component (mechanical or electrical) issues 
and system design related. This ranking was obtained by a combination of checking speed and the probability of occurrence.

Overview of symptom based error situations:

3.1.  Capacity shortage - General

Valid for both space heating and domestic hot water capacity shortage.

Capacity shortage - General ...........................................................37
Capacity shortage - Space heating .................................................40
Capacity shortage - Domestic hot water operation .........................41
The system does not start/operate .................................................42
Inaccurate temperature control (for both domestic hot water and 
space heating operation) ................................................................44
Water leakage or water release via the water pressure relieve valve

........................................................................................................45

Brine leakage..................................................................................46

Power consumption too high.......................................................... 46
Increased sound level - brine pump............................................... 47
Increased sound level - water pump .............................................. 48
Increased sound level - compressor .............................................. 48
Tapping water related..................................................................... 49
Compressor related ....................................................................... 50
Pump related.................................................................................. 52
User interface (no or strange display)............................................ 53

I

NFORMATION

In case of unit capacity shortage a special capacity boost setting [A-03] can be activated to increase the maximum 
compressor frequency from 148 Hz to 193 Hz (unit capacity increase from 10 to 12 kW).

Possible failures

Root cause

Check

Corrective action

Root cause category: software control

Compressor (M1C) frequency 
limited - high discharge tem-
perature protection function 
active.

In case the discharge temper-
ature is higher than 105°C the 
compressor frequency will be 
reduced. When the discharge 
temperature is lower than 
105°C the frequency can 
increase again.

Activation of the protection 
function can be caused by var-
ious reasons, therefore we 
recommend to check the fol-
lowing:
•  Check refrigerant charge
•  Check expansion valve for 

correct operation (see

 

page 72

) and check 

suction sensor R3T (see

 

page 58

).

• Check 

discharge 

thermistor (R2T) (see

 

page 58

).

Based on the diagnosis exe-
cute one of the following 
actions:
• Correct 

the 

refrigerant 

charge (total charge: 
1.8 kg).

•  Replace expansion valve 

(see

 page 133

, 

 page 135

) 

or suction sensor R3T (see

 

page 143

).

• Replace 

discharge 

thermistor R2T (see

 

page 143

).

Compressor (M1C) frequency 
limited - high pressure protec-
tion function active.

In case high pressure is higher 
than 38 barg the compressor 
frequency will be reduced. 
When the pressure drops 
below 36 barg the compressor 
frequency can increase again.

Activation of the protection 
function can be caused by var-
ious reasons, therefore we 
recommend to check the fol-
lowing:
•  Check high pressure 

sensor (see

 page 70

).

•  Check high pressure side 

plate type heat exchanger 
(see

 page 67

) for good 

water flow and heat 
exchange.

• Check 

the 

refrigerant 

charge.

Based on the diagnosis exe-
cute one of the following 
actions:
•  Replace high pressure 

sensor (see

 page 137

).

• Optimize 

the 

waterflow 

through the high pressure 
side plate type heat 
exchanger.

• Correct 

the 

refrigerant 

charge (total charge: 
1.8 kg).

Содержание EGSQH10S18AA9W









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EGSQH10S18AA9W

Waterous CX Series Operation And Maintenance Instruction preview
CX Series
Бренд: Waterous Страницы: 13
Waterous CX Series Overhaul Instructions preview
CX Series
Бренд: Waterous Страницы: 8
ubbink Cascademax Operating Manual preview
Cascademax
Бренд: ubbink Страницы: 29
YANGTECH EMP Series Operation Manual preview
EMP Series
Бренд: YANGTECH Страницы: 23
Vaillant aroTHERM plus Quick Manual preview
aroTHERM plus
Бренд: Vaillant Страницы: 40
Gardner Denver Elmo Rietschle V-VC 40 Original Operating Instructions preview
Elmo Rietschle V-VC 40
Бренд: Gardner Denver Страницы: 32
Powerhorse 109270 Owner'S Manual preview
109270
Бренд: Powerhorse Страницы: 48
Dometic 441003.701 Installation Instructions Manual preview
441003.701
Бренд: Dometic Страницы: 10
Stoll Gas Log Grate Heater Installation & Operating Instructions preview
Gas Log Grate Heater
Бренд: Stoll Страницы: 4
SHG Mini-CHIEMSEE B 1100 Operating Manual preview
Mini-CHIEMSEE B 1100
Бренд: SHG Страницы: 26
Pattfield Ergo Tools PE-SW 3030 Original Instructions Manual preview
PE-SW 3030
Бренд: Pattfield Ergo Tools Страницы: 162
Fenix Ecosun G 300 Instructions For Installation And Use Manual preview
Ecosun G 300
Бренд: Fenix Страницы: 12
Saab 400 106 639 Installation Instructions Manual preview
400 106 639
Бренд: Saab Страницы: 40
ubbink Cascademax Series Manual preview
Cascademax Series
Бренд: ubbink Страницы: 54
T.I.P. DIO 45/13 fl ex Translation Of Original Operating Instructions preview
DIO 45/13 fl ex
Бренд: T.I.P. Страницы: 52
SANNOVER CHAUFFAGE FRANCAIS LEXIA 500W Operation Manual preview
CHAUFFAGE FRANCAIS LEXIA 500W
Бренд: SANNOVER Страницы: 56
Lumax LX-1360 Manual preview
LX-1360
Бренд: Lumax Страницы: 28
Omega Altise OCON203B Operation, Maintenance And Safety Instructions preview
OCON203B
Бренд: Omega Altise Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды