background image

5 Configuration

Installation manual

18

EGSQH10S18AA9W

Daikin Altherma ground source heat pump

4P351747-1F – 2016.06

Leaving water temperature: Emitter type

#

Code

Description

[A.3.1.1.7]

[9-0B]

Reaction time of the system:

▪ 0 (Quick)(default)

Example: 

Small  water  volume  and

fan coils.

▪ 1 (Slow)

Example: 

Large  water  volume,  floor

heating loops.

Depending on the system water volume
and the heat emitters type, the heat up
of a space can take longer. This setting
can compensate for a slow or a quick
heating system by adjusting the unit
capacity during the heat up cycle.

5.2.6

Domestic hot water control

#

Code

Description

[A.4.1]

[6-0D]

Domestic hot water Type:

▪ 0  (Reheat  only)(default):  Only  reheat

operation is allowed.

▪ 1  (Reheat  +  sched.):  Same  as  2,  but

between the scheduled heatup cycles,
reheat operation is allowed.

▪ 2  (Scheduled  only):  The  domestic  hot

water  tank  can  ONLY  be  heated
according to a schedule.

[A.4.5]

[6-0E]

The maximum temperature that users
can select for the domestic hot water.
You can use this setting to limit the
temperature at the hot water taps.

INFORMATION

There is a risk of space heating capacity shortage/comfort
problem (in case of frequent domestic hot water operation,
frequent  and  long  space  heating  interruption  will  happen)
when  selecting  [6‑0D]=0  ([A.4.1]  Domestic  hot  water
Type=Reheat only).

5.2.7

Contact/helpdesk number

#

Code

Description

[6.3.2]

N/A

Number that users can call in case of
problems.

5.3

Advanced configuration/
optimization

5.3.1

Space heating operation: advanced

Room frost protection

NOTICE

If  Emergency  is  set  to  Manual  ([A.6.C]=0),  and  the  unit  is
triggered  to  start  emergency  operation,  the  user  interface
will ask confirmation before starting. Room frost protection
is  active  even  if  the  user  does  NOT  confirm  emergency
operation.

5.3.2

Heat source settings

Auto emergency

When  the  heat  pump  fails  to  operate,  the  backup  heater  can  serve
as  an  emergency  heater  and  either  automatically  or  non-
automatically take over the heat load.

▪ When auto emergency is set to Automatic and a heat pump failure

occurs,  the  backup  heater  will  automatically  take  over  the  heat
load.

▪ When  auto  emergency  is  set  to  Manual  and  a  heat  pump  failure

occurs, the domestic hot water and space heating operations will
stop  and  need  to  be  recovered  manually.  The  user  interface  will
then ask you to confirm whether the backup heater can take over
the heat load or not.

When the heat pump fails,   will appear on the user interface. If the
house  is  unattended  for  longer  periods,  we  recommend  to  set
[A.6.C] Emergency to Automatic.

#

Code

Description

[A.6.C]

N/A

Emergency:

▪ 0: Manual (default)

▪ 1: Automatic

INFORMATION

The  auto  emergency  setting  can  be  set  in  the  menu
structure of the user interface only.

INFORMATION

If a heat pump failure occurs and [A.6.C] is set to Manual,
the  room  frost  protection  function,  the  underfloor  heating
screed  dryout  function,  and  the  water  pipe  antifreeze
function  will  remain  active  even  if  the  user  does  NOT
confirm emergency operation.

5.3.3

System settings

Power consumption control

NOTICE

During  periods  of  excessive  capacity  demand  (example:
screed  dryout  function),  the  power  limitation  can  be
activated in accordance to the dimension of the brine earth
collector.

Содержание EGSQH10S18AA9W





























Отзывы: