Daiichi Electronics SDLC-105A, Инструкция по эксплуатации

Страница: 9 / 22

SDLC-207-104
8
2.5 Setting value
№ Contents Mark
Initial value
Setting range 2 contact
outputs
3 contact
outputs
4 contact
outputs
1 Unit display UNIT ％ ％,m,℃,m
３
/h,ppm,pH,TPm,×10kg,Ω,kW
2 Minimum value scaling MIN 0.0
-9999 to 9999 -9.99 to 99.99
-99.9 to 999.9 0.000 to 9.999
3 Maximum value scaling MAX 100.0
4
AL1
Output mode ALMD1 High High High
High：H operation，Low：L operation，
OFF ：With no operation
5 Operation value COMP1 70.0 80.0 80.0
It sets in the measurement display range
of -25 to +125％, and is a real scale.
6 Dead band D.B.1 3.0 0.5 to 50.0％
7 Excitation mode EXMD1 0N ON：Excitation，OFF：Non-excitation
8 Contact delay time (CD) C.D.1 0 0 to 180s
9
AL2
Output mode ALMD2 Low High High
High：H operation，Low：L operation，
OFF ：With no operation
10 Operation value COMP2 30.0 70.0 70.0
It sets in the measurement display range
of -25 to +125％, and is a real scale
11 Dead band D.B.2 3.0 0.5 to 50.0％
12 Excitation mode EXMD2 0N ON：Excitation，OFF：Non-excitation
13 Contact delay time (CD) C.D.2 0 0 to 180s
14
AL3
Output mode ALMD3 － Low Low
High：H operation，Low：L operation，
OFF ：With no operation
15 Operation value COMP3 － 30.0 30.0
It sets in the measurement display range
of -25 to +125％, and is a real scale
16 Dead band D.B.3 － 3.0 0.5 to 50.0％
17 Excitation mode EXMD3 － ON ON：Excitation，OFF：Non-excitation
18 Contact delay time (CD) C.D.3 － 0 0 to 180s
19
AL4
Output mode ALMD4 － Low
High：H operation，Low：L operation，
OFF ：With no operation
20 Operation value COMP4 － 20.0
It sets in the measurement display range
of -25 to +125％, and is a real scale
21 Dead band D.B.4 － 3.0 0.5 to 50.0％
22 Excitation mode EXMD4 － ON ON：Excitation，OFF：Non-excitation
23 Contact delay time (CD) C.D.4 － 0 0 to 180s
24 Starting delay time (SD) S.D. 5 1 to 180s
25 Bias point calibration CBIAS 0.00 -9.99 to 9.99％ (％ for input span)
26 Span point calibration CSPAN 0.00 -9.99 to 9.99％ (％ for input span)
27 Average number AVE 1 1，4，8，16，32
28 Prealarm PREAL OFF ON：Prealarm ON, OFF：Prealarm OFF
< Notes of setting >
・The decimal point position change of scaling is made by the minimum value scaling.
If the decimal point position is changed, the decimal point position of maximum value scaling and operation values
1 to 4 will also change. If the decimal point position is changed, please be sure to check the set value of
a maximum value scaling and an operation value.
・An operation value can be set up in -25 to +125％ of the measurement display range (minimum value scaling to
maximum value scaling).
(Example) Input 4 to 20mA, Operation value -25.0, Output mode is "Low" setting.
It becomes L detection in 0mA of inputs, it is also possible to use it as
disconnection detection.
・After setting change, in case a set value combination error occurs, it becomes a setting error display.
Please push the key and set up the right set value (in set value change mode).
125％
100％
50％
0％
-25％
24mA
20mA
12mA
4mA
0mA