5.2.5
Set IP Filter ...................................................................................................... 74
5.2.6
Set SMTP Parameter ....................................................................................... 76
5.2.7
Set UPnP Parameter ....................................................................................... 78
5.2.8
Set SNMP Parameter ...................................................................................... 79
5.2.9
Set Bonjour Parameter .................................................................................... 83
5.2.10
Set Multicast ................................................................................................. 84
5.2.11
Set 802.1x Parameter .................................................................................. 86
5.2.12
Set QoS Parameter ...................................................................................... 87
5.3
S
ET
PTZ
F
UNCTION
............................................................................................... 88
5.3.1
Set Preset ........................................................................................................ 88
5.3.2
Set Tour ........................................................................................................... 89
5.3.3
Set Scan .......................................................................................................... 90
5.3.4
Set Pattern ....................................................................................................... 91
5.3.5
Enable Pan ...................................................................................................... 92
5.3.6
Set PTZ Speed ................................................................................................ 93
5.3.7
Set Idle Motion ................................................................................................. 94
5.3.8
Set PowerUp .................................................................................................... 95
5.3.9
Set Time Task .................................................................................................. 96
5.3.10
PTZ Restart .................................................................................................. 98
5.3.11
Default .......................................................................................................... 99
5.4
E
VENT
................................................................................................................ 100
5.4.1
Set Smart Track ............................................................................................. 100
5.4.2
Set Video Detection ....................................................................................... 103
5.4.3
Set Audio Detection ....................................................................................... 112
5.4.4
Smart Plan ..................................................................................................... 114
5.4.5
Set IVS ........................................................................................................... 116
5.4.6
Set Face Detection ........................................................................................ 147
5.4.7
Set People Counting ...................................................................................... 149
5.4.8
Heat Map ....................................................................................................... 154
5.4.9
Set Alarm ....................................................................................................... 156
5.4.10
Abnormity ................................................................................................... 159
5.5
TORAGE
............................................................................................................ 163
5.5.1
Set Schedule ................................................................................................. 163
5.5.2
Destination ..................................................................................................... 167
5.5.3
Record Control ............................................................................................... 171
5.6
YSTEM
.............................................................................................................. 172
5.6.1
General .......................................................................................................... 172
5.6.2
Account .......................................................................................................... 175
5.6.3
Add Onvif User .............................................................................................. 180
