Dahua ARC5408C-CW Скачать руководство пользователя страница 22

Страница: 22 / 52

4.1.2.2

Disarm

You can disarm arming of alarm controller.

Step 1. Select SETUP>Zone Management>Arm/Disarm Zone.

Step 2. Set zone type to Global Arm, click OK. Confirmation box pops up.

Step 3. Input username and password, confirm. Device has two tone prompt as successfully

disarmed.

4.1.3 Alarm Program Keypad Arm/Disarm



Please refer to Alarm Programming Keypad User’s Manual for wired programming keypad.



Wireless alarm programming keypad is in Ch 5.4 and 5.5.

4.1.3.3

Arm

General Arm

Via keypad, arm the zone, alarm controller will response alarm signal in the zone.

Step 1. Press

key, to next level menu.

Step 2. By pressing

, select arm/disarm, press

Step 3. By pressing

, select arm, press

Step 4. Input arm type no., press

key.

Note:

Global arm

Instant arm

Out arm

Home Arm

Force to arm

Step 5. Input main user password, press

key.

If successfully arm, device buzzer has tone prompt, and enter exit delay status, according to

set exit dekay, buzzer once per 1s, and buzzer twice per 1s for last 10s. If failed, then dvice will

buzzer three times continuously. Now you shall check whether there is zone input, and you can

force to arm.

Quick Arm

In keypad homepage, input user password, device has tone prompt, and enter exit delay status,

according to set exit dekay, buzzer once per 1s, and buzzer twice per 1s for last 10s. If failed,

then dvice will buzzer three times continuously. Now you shall check whether there is zone input,

and you can force to arm.

Note:

Quick arm will only arm globally.

4.1.3.4

Disarm

General Disarm

Step 1. Press

key, to next level menu.

Содержание ARC5408C-CW





















































Результаты поиска

Содержание ARC5408C-CW

Отзывы:

Похожие инструкции для ARC5408C-CW

Бренды по названию

Популярные бренды

Dahua ARC5408C-CW, Быстрый старт

Результаты поиска

Содержание ARC5408C-CW

Отзывы:

Похожие инструкции для ARC5408C-CW

Бренды по названию

Популярные бренды