Daewoo KOR-131G0A Скачать руководство пользователя страница 32

Страница: 32 / 49

3. When there is no microwave oscillation

1) When touching

START

pad, oven lamp does not turn on.

Fan motor does not rotate, but cook indicator in display comes on.

Cause :

RELAY 2

does not operate.

refer to Circuit Diagram ( Point 3)

- Check method

2) When touching

START

pad, oven lamp turns on.

Fan motor and turntable rotate and cook indicator in display comes on.

Cause :

RELAY 1

does not operate.

refer to Circuit Diagram ( Point 2 )

- Check method

4. When the door is opened during operation, the count down timer does not stop.

refer to Circuit Diagram( Point 1 )

- Check method

5. When the digital clock does not operate properly.

refer to Circuit Diagram( Point 5 )

If clock does not keep exact time, you must check resistor R15,16, zener diodeZD1.

POINT
STATE

RELAY 2

- 5VDC

GND

RELAY 2

OFF

GND

- 12VDC

POINT
STATE

RELAY 1

-5VDC

GND

RELAY 1

OFF

GND

-12VDC

POINT
STATE

1) DOOR OPEN

OPEN

-5VDC

2) DOOR CLOSED

GND

CHECK

METHOD

REMEDY

Check the stage(ON,OFF) of the secondary interlock switch by
resistance measurement.

Replace secondary interlock
switch.

POINT

WAVE FORM

T: 16.

7 ms(60Hz)

PRINTED CIRCUIT BOARD

Содержание KOR-131G0A


















































Результаты поиска

Содержание KOR-131G0A

Отзывы:

Daewoo KOR-131G0A, Руководство по обслуживанию, Страница: 32 / 49

Результаты поиска

Содержание KOR-131G0A

Отзывы: