Daewoo KOR-131G0A Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 49

background image

19

KOR-131H4, KOR-131G4 and KOR-131S4

(1) Remove a screw which secure the wind guide assembly.

(2) Draw forward the wind guide assembly.

(3) Remove the noise filter from the guide wind.

(4) Pull the fan from the motor shaft.

(5) Remove two screws which secure the motor shaded pole.

(6) Remove the motor shaded pole.

(7) Reverse the above steps for reassembly.

9. To remove H.V.transformer.

1) Remove four screws holding the H.V.transformer.

2) Remove the H.V.transformer.

3) Reverse the above steps for reassembly.

DISASSEMBLY AND ASSEMBLY

«
...
18
19
20
21
22
...
»

Содержание KOR-131G0A


















































Отзывы:

Нет отзывов

Похожие инструкции для KOR-131G0A

Бренд: Jenn-Air Страницы: 2

Profile Advantium PSB9100DFBB

Бренд: GE Страницы: 2

Бренд: Oster Страницы: 10

Бренд: linarie Страницы: 11

Classic SFPA6301TV

Бренд: Smeg Страницы: 52

Бренд: AEG Electrolux Страницы: 44

Бренд: Hotpoint Страницы: 20

Бренд: KKT KOLBE Страницы: 40

B48FT68 0 Series

Бренд: NEFF Страницы: 68

Бренд: Saturn Страницы: 3

Бренд: Daewoo Страницы: 36

Бренд: La Germania Страницы: 32

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 31

Бренд: Haier Страницы: 8

Бренд: Haier Страницы: 17

Бренд: Haier Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды