background image

12

CIRCUIT DESCRIPTION

1. When the food is placed in the oven cavity and door is closed.

• The contact of the interlock monitor switch open (NO).
• The contacts of the primary interlock switch and secondary interlock switch close.

2. When the timer is set to the time desired.

• The contact of the timer switch close.
• Oven lamp turn on.
• 230V AC is applied to the high voltage transformer.
• Turntable motor start rotating and glass tray rotating.
• Fan motor rotating and cools the magnetron by blowing air.
• Timer motor operating and point to passing cooking time.
• 3.3 Volts AC is generated from the filamente winding of the high voltage transformer. This filament voltage is

applied to the magnetron to heat the magnetron filament through two noise preventing choke coils.

• A high voltage of 2000 Volts AC is generated in the secondary of high voltae transformer and this secondary

voltage is increased by the action of the diode and the charging of the high voltage capacitor. This resultant
D.C voltage is then applied to the anode of the magnetron. As shown in Fig. 2 the first half cycle of the high
voltage produces in the high voltage transformer secondary charges the high voltage capacitor. Current flow is
in the direction of the dotted-line during the second half cycle, the voltage produced by the transformer
secondary, and the charge of the high voltage capacitor are combined and applied to the magnetron as shown
by the solid line so that oscillations begins.
The disturbance wave generated by the magnetron is prevented by the choke coils of 1.5µH, filter capacitors of
500pF and the magnetron’s shielded case so that TV and radio programs are not impired by noise.

TM

TM

CL

GM

FM

CL

GM

FM

12A Fuse

Primary
Interlock
Switch

Timer
Switch

COM

NC

NO

Interlock
Monitor
Switch

Secondary
Interlock
Switch

Timer Motor

Cavity Lamp

Geared Motor

Fan Motor

Fig. 1

15A Fuse

Содержание KOG-36052S
































Отзывы: