background image

6

1. Steady, flat location.

This microwave oven should be set on a steady, flat surface.

2. Leave space behind and side.

All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and,
eventually, cause oven failure. 

3. Away from radio, and TV sets 

Poor television reception and radio interference may result if the oven is located close to a TV, Radio, or
antenna, feeder and so on.

4. Away from heating appliances and water taps

Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might
be adversely affected and breakdowns occur. 

5. Power supply 

• Check your local power source.

This microwave oven requires a current of approximately 12 amperes, 230V 50Hz.
Use a receptacle that will accept the earth prong.

• Voltage Warning

The voltage used must be the same as specified on this Microwave Oven.
Using a higher voltage may result in a fire or other accident causing oven damage. Using low voltage will
cause slow cooking.
We are not responsible for damage resulting from use of this Microwave Oven will a voltage or amperage
fuse other than those specified.

• Power supply cord is about 1.0  meters long. Do not use an extension cord.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard;

INSTALLATION

6. Examine the oven after unpacking for any damage such as: 

Dents, A misaligned door, Broken door, A dents in cavity.
If any of the above are visable, do not install this oven.

CAUTION  : Do not under any circumstances cut or remove the round earthing prog from this pulg.

CAUTION  : Maintenances works like the replacing of the power cable must be made by a technician

qualified of the after-sales-services.

WARNING  : This appliance must be earthed.

This wires in this mains lead are coloured inaccordance with the following code.

Green-and-yellow

: Earth

Blue

: Neutral

Brown

: Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked
with the letter ‘E’ or by the earth symbol or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter ‘N’ or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter ‘L’ or
coloured red.

IMPORTANT

Содержание KOG-36052S
































Отзывы: