61
Flame Sensor
1. Function
Ŗ5GPUQTHNCOGKUVJGUYKVEJVJCVQRGTCVGUD[FGVGEVKPIHWGNICU
ignition or heating of igniter.
Ŗ%QPVCEVRQKPVKUQRGPGFYJGPUWHHKEKGPVTCFKCPVJGCVKUFGVGEVGF
through the transparent window at the bottom of sensor.
Ŗ9JGPKIPKVGTKUUWHHKEKGPVN[JGCVGFVJKUKUFGVGEVGFVQVWTPQHHKIPKVGT
Then, state of internal contact point is continuously maintained to be
off by combustion heat of the ignited gas.
Ŗ9JGPICUUWRRN[KUEWVQHHUVCVGQHKPVGTPCNEQPVCEVRQKPVDGEQOGU QP CICKPUQVJCVVQGPCDNGTGŌKIPKVKQP
by igniter.
2. Specification
Ŗ#DKŌOGVCNUYKVEJVJCVKUQRGTCVGFD[TCFKCVKQPJGCV
Ŗ'NGEVTKETCVKPI8#
Ŗ1RGTCVKQPQRGPGFYKVJKP`UGEQPFUCHVGTUWKVCDNGTCFKCVKQPUVCTVUJGCVKPIKV
closed within 26~30 seconds after radiation heat disappears.
Ŗ6[RGPCOG45
3. Checking method of mal–function
Ŗ#VTQQOVGORGTCVWTGVJGTGKUVJGUVCVGQHUJQTVDGVYGGPVYQVGTOKPCNUQHVJKURCTV
Ŗ2CTVKUFGHGEVKXGKHTGUKUVCPEGDGVYGGPVGTOKPCNUOGCUWTGFCHVGTUGRCTCVKPIECDNGU
connected to sensor flame is 1
š
or more.
Ŗ2CTVKUFGHGEVKXGKHVJGCTGCDGVYGGPVGTOKPCNUKUPQVQRGPGFUGEQPFUCHVGTUGRCTCVKPI
sensor flame and holding flame of lighter near transparent window at the bottom
(less
than
1cm).
– Flame of lighter must be as long as the length of transparent window and
the flame must not be in direct contact with transparent window.
Ō6TCPURCTGPVYKPFQYQHUGPUQTHNCOGOWUVDGMGRVENGCPCVCNNVKOGUVQ
enable normal operation.
Ŗ2CTVKUFGVGEVKXGKHTGUKUVCPEGDGVYGGPVGTOKPCNUKUPQV
š
or less within 50
seconds after removing the flame of lighter.
Ŗ+PVJTGGQHVJGCDQXGEQPFKVKQPUUGPUQTHNCOGKUFGVGEVKXGVJGTGHQTGPGGFUVQDGTGRNCEGF
4. Procedure of replacement
①
Remove plate top.
②
Remove panel F ass'y.
③
Remove cabinet front ass'y.
④
Remove frame upper.
⑤
Remove drum ass'y.
⑥
%JGEMCVVCEJOGPVRQUKVKQP
⑦
Separate the connected cable and unfasten 1 screw to
separate parts.
⑧
Assemble part in reverse order of the above procedures.
Part Code : 3614825700
Laniter As
Sensor Flame
Содержание DWR-WG52S
