4
1. GENERAL
In the majority of cases, color television will need only slight
touch-up adjustment upon installation. Check the basic
characteristics such as height, focus and sub-bright.
Observe the picture for good black and white details without
objectionable color shading. If color shading is evident,
demagnetize the receiver. If color shading still persists, per-
for purity and convergence adjustments. this should be all
that is necessary to achieve optimum receive performance.
2. VERTICAL HEIGHT ADJUSTMENT
1) Tune in an active channel.
2) Adjust brightness and contrast control for a good picture.
3) Adjust vertical height control (R304) for approximately
one half inch over scan at top and bottom of picture
screen.
3. FOCUS ADJUSTMENT
1) Tune in an active channel.
2) Adjust brightness, sharpness and contrast controls for a
good picture, sharp scanning lines and/or sharp picture.
4. RF AGC ADJUSTMENT
1) Tune in an active channel.
2) Using the attenuator, apply the signal of 60dBµV to the
Antena input terminal
3) Turn RF AGC control (R106) so that it is 1.0V±0.3V
lower than maximum voltage.
5. HIGH VOLTAGE CHECK
High voltage is not adjustable but must be checked verify
that the receiver is operating within safe and efficient design
limitations as specified :
1) Operate Receiver for at least 15 minutes at 100-140V
AC line.
2) Set brightness, sharpness, contrast and color controls to
minimum position (Zero beam).
3) Connect an accurate high voltage meter to CRT anode.
The reading should be as follows.
If a correct reading connot be obtaines, check circuitry for
malfunctioning components.
6. X-RADIATION PROTECTION CIRCUIT TEST
When service has been performed on the horizontal deflec-
tion system, high voltage system or B+ system, the X-RADI-
ATION PROTECTION circuit must be tested for proper
operation as follows:
1) Operate receiver for at least 15 minutes at 120V AC line.
2) Confirm high voltage protector when R409 of power
PCB is connected to 30k
Ω
(1/4w) in parallel.
3) If high voltage protector is operated, remove 30k
Ω
(1/4w)
and confirm whether high voltage protector is still on.
4) Confirm normal operation on sound and video when
R410 is shorted.
7.WHITE VALANCE ADJUSTMENT
1) Receive MONOSCOPE PATTERN signal.
2) Set the each BIAS VR (VR903, VR904, VR905) and
DRIVE VR(VR901, VR902) to center position and Mini-
mize SCREEN using SCREEN VR on the side of FBT.
3) Open LEVER SW(S901) of CRT PCB.
4) Make straight and horizontal line by pushing service
key(V/H) on the SERVICE remocon.
5) Turn the SCREEN VR slowly until first color is bright-
ened and turn the concerned BIAS VR to the anticlock-
wise until that line's color is diappeared.
6) Turn the SCREEN VR slowly again until another color is
brightened and turn the concernde BIAS VR to the anti-
clockwise until that line's color is diappeared.
7) Turn the SCREEN VR slowly again until third color is
brightened and turn the concerned BIAS VR to the anti-
clockwise until that line's color is diappeared.
8) Adjust the BIAS VR to become white concerned line by
turning the BIAS VR in concerned with step 4-6, and 4-7
to clock direction (to be brightened).
9) Although you did step 4-5, 4-6, 4-7,
If it is not bright each step's color but bright first color,
stop turn the SCREEN VR at the position which color is
hardly to be seen, and concerned BIAS VR to clock
direction (to be brightened).
10) Turn LEVER SW(S901) of CRT PCB on.
11) Let the straight and horizontal line to be disappeared by
pushing service key(V/H) on the SERVICE remocon.
12) Set CONTRAST to maximize and set BRIGHT to
become center, and adjust WHITE BALANCE using R's
and B's DRIVE VR.
13) Inspect TRACKING of WHITE BALANCE by varying
CONTRAST and BRIGHT.
If you need to inspect again, Repeat step 4-5 to 4-9.
NOTE :
1. When performing any adjustments to resistor controls
and transformers use non-metallic screw driver or TV
alignment tools.
2. Before performing adjustments TV set must be on at
least 15 minutes.
■
■
GENERAL ADJUSTMENT
DVN-14F6N
24KV~26KV
DVN-20F6N
26KV~28KV
