Daewoo B20S-2 Скачать руководство пользователя страница 61

Страница: 61 / 68

Vehicle Systems

Disassembly & Assembly

Put steer axle (4) in position with a floor jack.

NOTE:

Install bolts (2) with approximately two bolt

threads into the mounting bosses.

Install bolts (2) and caps (3) in the mounting bosses.

Connect the hydraulic lines to the steering
cylinder.

Raise the steer axle with the floor jack, then
tighten bolts (2).

Connect hoses (1) to the steering lines.

Master Cylinder

Remove And Install Master Cylinder

Remove the rear floor plate from the lift truck. Drain
the brake fluid from the brake reservoir. Disconnect
hose (1) and line (4) from master cylinder (5).

Remove the cotter pin, washer and pin (3) from
the clevis and brake pedal.

Remove two bolts (2), the washers and master
cylinder (5) from the lift truck.

NOTE:

The following steps are for installation of the

master cylinder.

Put the master cylinder in position, and install the
two washers and bolts (2).

Install pin (3) through the master cylinder clevis
and brake pedal. Install the washer and cotter pin.

IDCD324S

IDCD321S

IDCD323S

Содержание B20S-2





































































Результаты поиска

Содержание B20S-2

Отзывы:

Похожие инструкции для B20S-2

Бренды по названию

Популярные бренды

Daewoo B20S-2, Разборка/Сборка

Результаты поиска

Содержание B20S-2

Отзывы:

Похожие инструкции для B20S-2

Бренды по названию

Популярные бренды