Installation Instructions
Verifying Proper Operation
WARNING
To ensure a safe and proper installation, the following
checklist should be completed by the installer to
ensure that no part of the installation has been
overlooked and the unit is working properly.
Proper installation is the responsibility of the
homeowner. The importance of proper installation of
your Dacor dishwasher cannot be overemphasized.
•
•
Pre-verification Check List
Make sure the power plug is disconnected.
Remove all packing material from inside the
dishwasher.
Check the orientation of the bottom door seal. The seal
“bulb” should be facing into the tank. If it is oriented
towards the exterior of the door, open the dishwasher
door fully and orientate the door seal so that it is facing
in to the tank.
Familiarize yourself with the dishwasher operations by
reading the use and care manual.
Remove any protective film, if present, from the control
panel, door panel, etc.
Verify that all electrical wiring is secure and is not being
pinched or in contact with door springs or any other
dishwasher components.
Verify that the dishwasher is level by pulling the lower
rack about half way out. Let go of the rack and make
sure it does not roll in or out. If it does, re-level the
dishwasher.
Add two quarts of water to the bottom of the
dishwasher to lubricate the pump seal.
Turn on the water supply and check for plumbing leaks.
Tighten connections if necessary.
Verify that the door springs do not come in contact with
any dishwasher components.
Verify the hot water temperature by turning on the
hot water faucet at the sink. The water going to the
dishwasher must be between 120ºF and 150ºF.
Wet Test Check List
Plug in the dishwasher power cord.
Program dishwasher to run a short wash. See the use
and care manual for specific operating instructions.
Close the door completely.
□
□
□
□
□
□
□
□
□
□
□
□
□
□
You should hear the dishwasher drain and then begin
to fill with water. Wait approximately two (2) minutes,
then carefully open the door to verify water is filling the
dishwasher tank. If there is water present, close the
door and continue the process. Should the water not fill
the tank or the pump is not running, then immediately
push the
START/STOP
button to stop the dishwasher
and verify that the water source is turned on and that
the power cord is plugged in. Make sure power to the
electrical outlet is switched on at the circuit breaker
panel or fuse box.
Check for leaks under the dishwasher. If any leaks are
found, immediately push the
START/STOP
button and
disconnect the power plug. Tighten the water supply
connections. Reconnect power and restart the cycle.
Check for leaks around the door. A leak around the
door could be caused by the dishwasher door rubbing
or hitting against adjacent cabinets. Disconnect power
and reposition and/or re-square the dishwasher if
necessary. Restart the unit after repositioning.
The dishwasher will drain after the first fill. Check the
drain line for leaks. If leaks are found, immediately
push the
START/STOP
button and disconnect the
power plug. Tighten the drain connections. Reconnect
power and restart the cycle.
Open the dishwasher door and verify that most of the
water has drained. If not, verify that the disposer plug
has been removed and/or the air gap is not plugged.
Run the dishwasher through another fill and drain
cycle. Verify that there are no leaks.
If the dishwasher does not operate correctly, see the
instructions below.
If the fill, wash and drain cycles operate properly,
reinstall the toe kick mounting plate. Adjust the toe
kick to cover legs and snap it into place on the toe kick
mounting plate. See page 12 for instructions.
If the dishwasher fails to operate properly:
Verify that power is supplied to the dishwasher.
Check all plumbing connections.
Repeat the above test.
If the appliance still does not work, contact the Dacor
Customer Service Team at (800) 793-0093.
Do not attempt to repair the appliance yourself. Dacor
is not responsible for service required to correct a faulty
installation.
□
□
□
□
□
□
□
□
•
•
•
•