background image

SAVE THESE INSTRUCTIONS

Important Safety Instructions

English

8

 

To avoid the possibility of explosion or fire

, do not store or use combustible, flammable 

or explosive vapors and liquids (such as gasoline) inside or in the vicinity of this or any 
other appliance. Also keep items that could explode, such as aerosol cans away from 
cooktop burners, ovens and range hoods. Do not store flammable or explosive materials in 
adjacent cabinets or areas.

WARNING

IMPORTANT

: This appliance is equipped with a three-prong grounding electric plug for 

protection against possible electric shock hazards. It must be plugged into a dedicated, 
grounded, electrical outlet. If only a two-prong electrical outlet is available, it is the 
responsibility of the customer to have it replaced with a dedicated, properly grounded 
three-prong electrical outlet.

Do not kink or pinch the power supply cord of the appliance.

Never unplug the appliance by pulling on the power cord.

Always grip the plug firmly and pull straight out from the electrical outlet.

Disconnect this appliance when not in use.

Do not install, repair, modify, or replace any part of the appliance unless specifically
recommended in the literature accompanying it.

A qualified service technician should perform all other services.

DO NOT

 cut or remove the third (ground) 

prong from the power cord. 

DO NOT

 use an adapter plug. 

DO NOT

 use a power cord that is frayed or 

damaged. 

DO NOT

 connect the appliance to an 

extension cord. Keep the power cord away 
from heated surfaces.

NOTE

Use of an electrical outlet with a
ground.

Use of an electrical outlet with a
ground fault interrupter (GFI) is not
recommended.

Содержание DRW24980RAP/LAP









































































Отзывы: