background image

SAVE THESE INSTRUCTIONS

English

6

 

Important Safety Instructions

The Important safety instructions and warnings in these instructions are not meant to 
cover all possible problems and conditions that can occur.

Use common sense and caution when installing, maintaining, or operating this or any 
other appliance.

Always contact the Dacor Customer Assurance Team about problems and conditions that 
you don’t understand. See 

Customer-Service Information

.

Safety symbols and labels

These alerts are meant to bring attention to important areas in the manual.

Whenever you see these symbols or labels, read the message carefully before continuing.

DANGER

Immediate hazards that 

WILL

 cause severe personal injury or death.

WARNING

Hazards or unsafe practices that 

MAY 

cause in severe personal injury or death.

CAUTION

Hazards or unsafe practices that 

MAY 

cause in minor personal injury or property damage.

State of California Proposition 65 Warning (US only)

WARNING

 : This product contains chemicals known to the State of California to cause 

cancer and birth defects or other reproductive harm.

Содержание DRW24980RAP/LAP









































































Отзывы: