background image

5

SUggESTED METHODS OF INSTALLATION

Offset mounting, recessed above ceiling. For plaster, dry 

wall, tile or paneling. Bottom of case painted same finish 

as ceiling.

Offset mounting, recessed above ceiling. May be 

adapted for 3/4" ceiling, but cut to 1/4" thick under 

screen case and panel.

NOTE:
MUST MARK HOLE LOCATION OF SCREWS IN 3-1/2" PANEL FOR REMOVAL, IF COVERING WITH TILE.

Offset mounting, recessed above ceiling. May be 

adapted for 1/4" paneling for ceiling.

Flush mounting, recessed above ceiling. For use with 

dropped ceiling. May also be adapted for use with 

acoustical or other ceiling 3/4" thick but cut to 1/4" thick 

under screen case and panel.

 

METHOD A 

METHOD B

 

METHOD C 

METHOD D

(SUGGESTED) 

1/4" LAG 

SCREWS

1-1/2"

1-1/2"

MOUNTING 

jOIST

3/4" FINISHED 

CEILING

3-1/2" 

PANEL

CAN BE PAINTED SAME AS CEILING 

OR REMOVED AND REPLACED WITH 

FINISHED CEILING

ALUMINUM SLAT

9-3/16"

9"

MOUNTING 

BRACKET

8-11/16"

FURRING 

STRIP

PICTURE SURFACE

MASKING SURFACE

3/16" x 1" STEEL BAR 

IN POCKET

(SUGGESTED)  

1/4" LAG 

SCREWS

1-1/2"

1-1/2"

MOUNTING 

jOIST

3/4" FINISHED 

CEILING

3-1/2" 

PANEL

CEILING TILE CUT TO 1/4" THICK 

(ATTACH WITH MASTIC)

ALUMINUM SLAT

9-3/16"

9"

MOUNTING 

BRACKET

8-15/16"

FURRING 

STRIP

PICTURE SURFACE

MASKING SURFACE

3/16" x 1" STEEL BAR 

IN POCKET

(SUGGESTED)  

1/4" LAG 

SCREWS

1-1/2"

1-1/2"

MOUNTING 

jOIST

FINISHED 

CEILING

3-1/2" 

PANEL

ALUMINUM SLAT

9-3/16"

9"

MOUNTING 

BRACKET

8-15/16"

FURRING 

STRIP

PICTURE SURFACE

MASKING SURFACE

3/16" x 1" STEEL BAR 

IN POCKET 

1-1/2"

MOUNTING 

jOIST

SUSPENDED 

CEILING 

TILE

3/16" x 1" STEEL BAR 

IN POCKET

MASKING SURFACE

PICTURE SURFACE

FURRING 

STRIP

8-15/16"

1-1/2"

(SUGGESTED)  

1/4" BOLTS

3-1/2" 

PANEL

T-BAR FURNISHED 

WITH CEILING

ALUMINUM SLAT

TENSIONED DUAL MASkINg ELECTROL

®

 INSTRUCTIONS

CASE LENGTH = SCREEN FABRIC WIDTH

+ 15-3/4", ALL SIzES

1-1/2"

MOUNTING BRACKET

MOTOR END

9"

ELECTRICAL OUTLET

7-7/8"

7-7/8"

8-11/16"

8' AND WIDER SCREENS ONLY

Содержание TENSIONED DUAL MASKING ELECTROL









Отзывы: