background image

3

SCREEN ADJUSTMENT FOR 120V SCREENS

 

  CAUTION! THE MASK SHOULD NOT BE FIELD ADjUSTED FOR MORE OR LESS DROP.

Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly ad-

justed at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner:

NOTE:

 Use a screw driver or allen wrench to make adjustments.

MORE SCREEN DROP

  1.  Remove access panel (Fig. 1).
  2.  Place operating switch in 

“down”

 position.

  3.   When the screen stops, turn the 

“down”

 limit knob (Fig. 2) one-quarter turn counterclockwise. Test by raising picture 

surface approximately two feet, then lower again. Repeat until desired picture surface position is attained.

 

  NOTE: Stop adjustment when string screws reach the bottom of roller and there is no wraps of string around the roller. Beyond 

this point the roller will start pulling up the aluminum slat, the fabric will still be coming down and severe damage to the fab-
ric will occur!

  4.   Replace access panel.

LESS SCREEN DROP

  1.  Remove access panel. (Fig. 1).
  2.   Raise picture surface approximately two feet above desired level.
  3.   Place operating switch in 

“off”

 position.

  4.   Turn the 

“down”

 limit knob (Fig. 2) one-quarter turn clockwise. Test by raising picture surface approximately two 

feet, then lower again. Repeat until desired picture surface position is attained.

  5.  Replace access panel.

s

!

DOWN

BLACK

UP

DOWN

COMMON

WHITE

COMMON

GROUND

GREEN

GROUND

MASK

SCREEN

UP

DOWN

MaSK MOTOR

4 – WIRE 

MASK MOTOR

UP

OFF

DOWN

4 – WIRE 

SCREEN MOTOR

SCReeN MOTOR

115V. a.C. 60 CyCLe

BLACK (HOT)

BLACK

RED

WHITE

WHITE (COMMON)

GREEN

GROUND WIRE

RED

UP

115V DUAL MOTOR 

CONTROL

TENSIONED DUAL MASkINg ELECTROL

®

 INSTRUCTIONS

Содержание TENSIONED DUAL MASKING ELECTROL









Отзывы: