background image

2

PRE-INSTALLATION

1.  Carefully unpack screen and remove outer wrapping from case.
2.  Make sure to recheck measurements of screen location before installation.
3.  Remove center support brackets (on 8' and wider screens only), reverse brackets and reinstall flush with the top of the 

box.

INSTALLATION

  1.  Install screen by raising unit into position between joists at one end only. Install one lag screw in each mounting 

bracket.

  2.  Level unit lengthwise with a carpenter’s level and plumb level. Secure opposite end.

 

CAUTION! Do not seal in until screen has been secured in position and properly tested for satisfactory operation.

  3.  Carefully remove three shipping brackets by removing six hex head screws from case and three phillips head 

screws from aluminum slat. Use a phillips screwdriver, a hex socket and a ratchet. Slat should move freely (Fig. 1).

  4.  Detach access panel by removing screws (Fig. 1).
  5.  Remove junction box cover plate.
  6.  Install electric hook up that applies to your unit. Make sure to review your electrical installation checklist and wiring 

diagram (included) for either 120 volt switch, 220/240 volt switch or low voltage control.

 

 

NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), 

 

  CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.

 

   

CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.

 

7.  Carefully remove two wood boards securing mask surface to case.

  8.  Test installation by carefully running picture and mask surfaces up and down several times. Be prepared to stop 

screen. Standard Duty Cycle: 1 MIN. ON / 3 MIN. OFF.

 

 

NOTE: When rolled down, the picture surface should wrap fully around the roller.  No part of the roller should be exposed.  
Picture and mask surfaces will automatically stop in the down position.

 

 

The mask will start down off the front of the roller, travel completely down past the bottom of the viewing surface,   

 

  then “step back” against the viewing surface to eliminate shadowing by rolling up the back side of the roller. Do not  

 

  adjust the limits to change this feature. 

  9.  Run the picture and mask surfaces upward. When the picture and mask surfaces are fully up the limit switches (in    

 

  the motors) are tripped and the motors shut off.

  10.  Check for satisfactory condition by operating screen a few times. Reinstall access panel.

s

!

s

!

 

FIGURE 1 

FIGURE 2

DRyWaLL 

SCReW

aCCeSS PaNeL

MaChINe SCReW

PhILLIPS heaD SCReW

ShIPPING BRaCKeT

aDjUSTMeNT 

KNOB 

“UP”

PICTURe SURFaCe

MaSK SURFaCe

aDjUSTMeNT 

KNOB 

“DOWN”

MaSK MOTOR

SCReeN MOTOR

heX heaD SCReW

Содержание TENSIONED DUAL MASKING ELECTROL









Отзывы: