D-Link xStack DES-3500 Series Скачать руководство пользователя страница 247

Страница: 247 / 260

DES-3500 Layer 2 Fast Ethernet Switch CLI Reference Manual

244

enable sim

Purpose

Used to enable Single IP Management (SIM) on the Switch

Syntax

enable sim

Description

This command will enable SIM globally on the Switch. SIM features
and functions will not function properly unless this function is
enabled.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To enable SIM on the Switch:

DES-3500:admin#enable sim

Command: enable sim

Success.

DES-3500:admin#

disable sim

Purpose

Used to disable Single IP Management (SIM) on the Switch

Syntax

disable sim

Description

This command will disable SIM globally on the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable SIM on the Switch:

DES-3500:admin#disable sim

Command: disable sim

Success.

DES-3500:admin#

show sim

Purpose

Used to view the current information regarding the SIM group on the
Switch.

Syntax

show sim {[candidates {<candidate_id 1-32>} | members
{<member_id 1-32>} | group {commander_mac <macaddr>}] |
neighbor]}

Description

This command will display the current information regarding the SIM
group on the Switch, including the following:

SIM Version - Displays the current Single IP Management version on

Содержание xStack DES-3500 Series





































































































































































































































































Результаты поиска

Содержание xStack DES-3500 Series

Отзывы:

Похожие инструкции для xStack DES-3500 Series

Бренды по названию

Популярные бренды

D-Link xStack DES-3500 Series, Руководство CLI

Результаты поиска

Содержание xStack DES-3500 Series

Отзывы:

Похожие инструкции для xStack DES-3500 Series

Бренды по названию

Популярные бренды