D-Link xStack DES-3500 Series Скачать руководство пользователя страница 52

Страница: 52 / 260

DES-3500 Layer 2 Fast Ethernet Switch CLI Reference Manual

DES-3500:admin#config snmp system_location HQ 5F

Command: config snmp system_location HQ 5F

Success.

DES-3500:admin#

config snmp system_name

Purpose

Used to configure the name for the Switch.

Syntax

config snmp system_name {<sw_name>}

Description The

config snmp system_name

command configures the name of

the Switch.

Parameters

<sw_name>

- A maximum of 255 characters is allowed. A NULL

string is accepted if no name is desired.

Restrictions

Only Administrator and Operator-level users can issue this
command.

Example usage:

To configure the Switch name for “

DES-3526 Switch

”:

DES-3500:admin#config snmp system_name DES-3526 Switch

Command: config snmp system_name DES-3526 Switch

Success.

DES-3500:admin#

enable rmon

Purpose

Used to enable RMON on the Switch.

Syntax

enable rmon

Description

This command is used, in conjunction with the

disable rmon

command below, to enable and disable remote monitoring (RMON)
on the Switch.

Parameters None.

Restrictions

Only Administrator and Operator-level users can issue this
command.

Example Usage:

To enable RMON:

DES-3500:admin#enable rmon

Command: enable rmon

Success.

DES-3500:admin#

Содержание xStack DES-3500 Series





































































































































































































































































Результаты поиска

Содержание xStack DES-3500 Series

Отзывы:

Бренды по названию

Популярные бренды

D-Link xStack DES-3500 Series, Руководство CLI

Результаты поиска

Содержание xStack DES-3500 Series

Отзывы:

Бренды по названию

Популярные бренды