D-Link DGS-3312SR Скачать руководство пользователя | Manualshive

Страница: 135 / 283

background image

DGS-3312SR Stackable Gigabit Layer 3 Switch

122

RIP Command Codes

The field VERSION contains the protocol version number (1 in this case), and is used by the receiver to verify which
version of RIP the packet was sent.

RIP 1 Message

RIP is not limited to TCP/IP. Its address format can support up to 14 octets (when using IP, the remaining 10 octets must
be zeros). Other network protocol suites can be specified in the Family of Source Network field (IP has a value of 2). This
will determine how the address field is interpreted.

RIP specifies that the IP address, 0.0.0.0, denotes a default route.

The distances, measured in router hops are entered in the Distance to Source Network, and Distance to Destination
Network fields.

RIP 1 Route Interpretation

RIP was designed to be used with classed address schemes, and does not include an explicit subnet mask. An extension to
version 1 does allow routers to exchange subnetted addresses, but only if the subnet mask used by the network is the same
as the subnet mask used by the address. This means the RIP version 1 cannot be used to propagate classless addresses.

Routers running RIP version 1 must send different update messages for each IP interface to which it is connected.
Interfaces that use the same subnet mask as the router’s network can contain subnetted routes, other interfaces cannot. The
router will then advertise only a single route to the network.

RIP Version 2 Extensions

RIP version 2 includes an explicit subnet mask entry, so RIP version 2 can be used to propagate variable length subnet
addresses or CIDR classless addresses. RIP version 2 also adds an explicit next hop entry, which speeds convergence and
helps prevent the formation of routing loops.

RIP2 Message Format

The message format used with RIP2 is an extension of the RIP1 format:

RIP version 2 also adds a 16-bit route tag that is retained and sent with router updates. It can be used to identify the origin
of the route.

Because the version number in RIP2 occupies the same octet as in RIP1, both versions of the protocols can be used on a
given router simultaneously without interference.

«
...
133
134
135
136
137
...
»

Содержание DGS-3312SR




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3312SR

Бренд: JB Systems Light Страницы: 15

Sierra Pro XL 1616V3

Бренд: Kramer Страницы: 2

Бренд: I/O Interconnect Страницы: 27

Бренд: GE Страницы: 2

Бренд: Kobold Страницы: 10

Бренд: N-Tron Страницы: 20

Бренд: PKP Страницы: 11

Бренд: Endress+Hauser Страницы: 25

Бренд: CYP Страницы: 20

Бренд: GeoVision Страницы: 7

Бренд: Campbell Hausfeld Страницы: 4

Бренд: VADA Страницы: 4

Бренд: Larson Electronics Страницы: 2

ControlZAPP CZ CESR 10VDC

Бренд: DANLERS Страницы: 2

SecureStack B2 B2G124-48P

Бренд: Enterasys Страницы: 91

IDAN-LAN25255HR

Бренд: rtd Страницы: 24

Бренд: Elk Products Страницы: 2

Бренд: Kramer Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды