D-Link DGS-3130-30TS Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 83

background image

DGS-3130 Series Layer 3 Stackable Managed Switch Hardware Installation Guide

15

Figure 2-6 LED indicators for the DGS-3130-30S

LED

Description

Power

This LED will light solid green after the Switch has been powered on
successfully.

This LED will be off when the Switch is no longer receiving power (i.e. powered
off).

Console

This LED will light solid green when the RJ45 console port is active.

This LED will blink when activity on this port is taking place.

This LED will be off when console ports are not active.

MGMT

The LED at the left side indicates the status of MGMT port.

This LED will light solid green or amber after a link to the MGMT port was
successfully established.

This LED will blink when activity on this port is taking place.

This LED will be off when MGMT port is not active.

RPS

This LED will light green when the Redundant Powers Supply is in use.

This LED will be off when the RPS is not in use.

Fan Err

This LED will light solid red when the fan fails.

This LED will be off when the fan is operating normally.

USB

This LED will light solid green if a USB flash drive is plugged in.

This LED will blink green when the Switch is reading or writing data to and from
the USB drive.

This LED will be off when no USB drive is plugged into the USB port.

This LED will light solid red when a USB drive failure has been detected.

Link/Act LEDs

The Switch has LED indicators for Link and Activity.

SFP Ports:

The triangle LED indicates the Link/Act status of SFP ports. This

LED will light solid green when there is a connection (or link) to a 1000 Mbps
Ethernet device or solid amber when there is a connection (or link) to a 100
Mbps Ethernet device on any of the SFP ports. The LED will blink green when
a 1000 Mbps port is active or blink amber when a 100 Mbps port is active. The
LED will be off when there is no link or activity.

10G RJ45 Ports:

The LED at the left side indicates the Link/Act status of

upper 10G RJ45 ports. The LED at the right side indicates the Link/Act status
of lower 10G RJ45 ports. This LED will light solid green when there is a
connection (or link) to a 10 Gbps Ethernet device or solid amber when there is
a connection (or link) to a 100/1000 Mbps Ethernet device on any of the RJ45
ports. The LED will blink green when a 10 Gbps port is active or blink amber
when a 100/1000 Mbps port is active. The LED will be off when there is no link
or activity.

SFP+ Ports:

The triangle LED indicates the Link/Act status of 10G SFP+ ports.

This LED will light solid green when there is a connection (or link) to a 10 Gbps
Ethernet device or solid amber when there is a connection (or link) to a 1 Gbps
Ethernet device at any at any of the SFP+ ports. The LED will blink green

«
...
13
14
15
16
17
...
»

Содержание DGS-3130-30TS




















































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3130-30TS

Бренд: 4O3A Страницы: 2

Бренд: Ubiquiti Страницы: 24

Бренд: Ubiquiti Страницы: 13

Бренд: Ubisys Страницы: 2

Бренд: Kramer Страницы: 2

Бренд: IOGear Страницы: 1

SmartNode 4658 Series

Бренд: Patton electronics Страницы: 12

Бренд: Setra Systems Страницы: 4

CentreCOM GS970M Series

Бренд: Allied Telesis Страницы: 21

Бренд: G-Lab Страницы: 12

Бренд: Nextech Страницы: 4

Centerpoint 2x16

Бренд: Epicenter Страницы: 25

Бренд: Edimax Страницы: 2

Бренд: Davey Страницы: 2

Бренд: Orei Страницы: 27

Бренд: Cypress Страницы: 16

Бренд: TRENDnet Страницы: 2

Бренд: T.I.P. Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды