manualshive.com logo in svg

Cypress Semiconductor MoBL-USB CY7C68053, Техническое описание, Страница: 23 / 39

Поделиться
Скачать
Cypress Semiconductor MoBL-USB CY7C68053 Скачать руководство пользователя страница 23

CY7C68053

Document # 001-06120 Rev *F

Page 23 of 39

6.0

 Absolute Maximum Ratings

Storage Temperature ...........................................................................................................................................– 65°C to +150°C
Ambient Temperature with Power Supplied
Industrial ................................................................................................................................................................– 40°C to +85°C
Supply Voltage to Ground Potential
For 3.3V Power domain .......................................................................................................................................... – 0.5V to +4.0V
For 1.8V Power domain .......................................................................................................................................... – 0.5V to +2.0V
DC Input Voltage to Any Input Pin
For pins under 3.3V Power Domain.................................................................................................................................... 3.6V

[14]

For pins under 1.8V - 3.3V Power Domain (GPIO’s) ............................................................................................1.89V to 3.6V

[14]

(The GPIO’s are not over voltage tolerant, except the SCL and SDA pins, which are 3.3V tolerant)
DC Voltage Applied to Outputs in High Z State............................................................................................  – 0.5V to VCC

 

+ 0.5V

Maximum Power Dissipation
From AVcc Supply ............................................................................................................................................................... 90 mW
From IO Supply.................................................................................................................................................................... 36 mW
From Core Supply................................................................................................................................................................ 95 mW
Static Discharge Voltage ....................................................................................................................................................> 2000V
(I2C SCL and SDA pins only ... >1500V)
Maximum Output Current, per I/O port ................................................................................................................................. 10 mA

7.0

 Operating Conditions

T

A

 (Ambient Temperature Under Bias) 

Industrial ............................................................................................................................................................... – 40°C to +85°C
Supply Voltage
3.3V Power Supply ......................................................................................................................................................3.0V to 3.6V
1.8V Power Supply ...................................................................................................................................................1.71V to1.89V
Ground Voltage ........................................................................................................................................................................... 0V
F

OSC 

(Oscillator or Crystal Frequency) ............................................................................................................. 24 MHz ± 100 ppm

............................................................................................................................................................................ Parallel Resonant

........................................................................................................................................................................... 500 

µ

W drive level

Load capacitors 12 pF

Note

14. It is recommended to not power I/O when chip power is off.

[+] Feedback 

Содержание MoBL-USB CY7C68053








































Отзывы:

Нет отзывов