manualshive.com logo in svg

Cypress Semiconductor MoBL-USB CY7C68053, Техническое описание, Страница: 12 / 39

Поделиться
Скачать
Cypress Semiconductor MoBL-USB CY7C68053 Скачать руководство пользователя страница 12

CY7C68053

Document # 001-06120 Rev *F

Page 12 of 39

4.1

CY7C68053 Pin Descriptions 

Note

9.

Unused inputs must not be left floating. Tie either HIGH or LOW as appropriate. Outputs should only be pulled up or down to ensure signals at power up and 

in standby. Note also that no pins should be driven while the device is powered down

Table 4-1.  FX2LP18 Pin Descriptions

[9]

56 VFBGA

Name

Type

Default

Description

2D

AV

CC

Power

N/A

Analog VCC

. Connect this pin to 3.3V power source. This signal provides 

power to the analog section of the chip.

Appropriate bulk/bypass capacitance should be provided for this 

supply rail.

1D

AV

CC

Power

N/A

Analog VCC

. Connect this pin to 3.3V power source. This signal provides 

power to the analog section of the chip. 

2F

AGND

Ground

N/A

Analog Ground

. Connect this pin to ground with as short a path as 

possible.

1F

AGND

Ground

N/A

Analog Ground

. Connect to this pin ground with as short a path as 

possible.

1E

DMINUS

I/O/Z

Z

USB D– Signal

. Connect this pin to the USB D– signal.

2E

DPLUS

I/O/Z

Z

USB D+ Signal

. Connect this pin to the USB D+ signal. 

8B

RESET#

Input

N/A

Active LOW Reset

. This pin resets the entire chip. See Section 3.9 ”Reset 

and Wakeup” on page 5 for more details.

1C

XTALIN

Input

N/A

Crystal Input

. Connect this signal to a 24 MHz parallel resonant, funda-

mental mode crystal and load capacitor to GND. 

It is also correct to drive XTALIN with an external 24-MHz square wave 

derived from another clock source.

2C

XTALOUT

Output

N/A

Crystal Output

. Connect this signal to a 24 MHz parallel resonant, funda-

mental mode crystal and load capacitor to GND.

If an external clock is used to drive XTALIN, leave this pin open.

2B

CLKOUT

O/Z

12 MHz

CLKOUT.

 12-, 24- or 48-MHz clock, phase locked to the 24 MHz input 

clock. The 8051 defaults to 12 MHz operation. The 8051 may tri-state this 

output by setting CPUCS.1 = 1.

Port A

8G

PA0 or

INT0# 

I/O/Z

I

(PA0)

Multiplexed pin whose function is selected by PORTACFG.0 

PA0

 is a bidirectional IO port pin.

INT0#

 is the active LOW 8051 INT0 interrupt input signal, which is either 

edge triggered (IT0 = 1) or level triggered (IT0 = 0).

6G

PA1 or

INT1# 

I/O/Z

I

(PA1)

Multiplexed pin whose function is selected by: 

PORTACFG.1

PA1

 is a bidirectional IO port pin.

INT1#

 is the active LOW 8051 INT1 interrupt input signal, which is either 

edge triggered (IT1 = 1) or level triggered (IT1 = 0).

8F

PA2 or

SLOE

I/O/Z

I

(PA2)

Multiplexed pin whose function is selected by two bits: 

IFCONFIG[1:0].

PA2

 is a bidirectional IO port pin.

SLOE

 is an input-only output enable with programmable polarity 

(FIFOPINPOLAR.4) for the slave FIFO’s connected to FD[7:0] or FD[15:0].

7F

PA3 or 

WU2

I/O/Z

I

(PA3)

Multiplexed pin whose function is selected by:

WAKEUP.7 and OEA.3

PA3

 is a bidirectional IO port pin.

WU2 

is an alternate source for 

USB Wakeup,

 enabled by WU2EN bit 

(WAKEUP.1) and polarity set by WU2POL (WAKEUP.4). If the 8051 is in 

suspend and WU2EN = 1, a transition on this pin starts up the oscillator 

and interrupts the 8051 to allow it to exit the suspend mode. Asserting this 

pin inhibits the chip from suspending, if WU2EN = 1. 

[+] Feedback 

Содержание MoBL-USB CY7C68053








































Отзывы:

Нет отзывов