background image

AspectFT-Matrix MAX Area Controller Installation Guide (1/05/2015)

1-1

1.1   A

SPECT

FT-M

ATRIX

 MAX I

NTRODUCTION

Unpack your AspectFT-Matrix MAX Area Controller and inspect the contents for damaged or missing 
items. Included in this package, you should find the following items:

.

AspectFT-Matrix MAX Area Controller 

.

AspectFT-Matrix MAX Controller Hardware Installation Guide (this document)

1.1.1 T

OOLS

 R

EQUIRED

The following tools and supply may be required for installation:

.

Small flat-bladed screwdriver - for field-bus and power connectors

.

Drill - for mounting the product onto a wall

.

Wire-strippers - for terminating EIA-485 connections

1.1.2 S

AFETY

 P

RECAUTIONS

NOTE

All equipment must be installed in accordance with 
NEC and local codes.  For more information on 
local codes, please check state/local regulations in 
your area.

CAUTION

To prevent damage to any of the electrical 
components of this product and to ensure that it 
continually operates, do not attempt to alter any 
componentry.

S

ECTION

 1

H

ARDWARE

 I

NSTALLATION

The following document provides general information relative to the hardware installation of the AspectFT-
Matrix MAX Area Controller hardware. Please read through this document carefully before proceeding with 
the hardware installation process.

Содержание American Auto-Matrix Aspect Matrix MAX













Отзывы: