CVE JC300 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 31

CVE JC300 Скачать руководство пользователя страница 16

Page 16

WARNING

Danger of electric shock.

All repairs must be

carried out by personnel authorised by the

machine’s manufacturer or by duly trained

and qualified personnel. Please refrain from

opening any lids, guards or spare parts unless

specifically required to do so in the user

documentation.

WARNING

Fuel.

Unless otherwise indicated in the user

documentation, please remember to always

empty the machine’s fuel engine before

replacing any component.

WARNING

Hazardous chemical products during

maintenance.

When working with hazardous

degreasing materials or cleaning the machine,

please use cloths, and then clean these

elements using a neutral solution.

WARNING

Do not carry out any maintenance tasks whilst

the motor is in operation.

WARNING

Please only use manufacturer approved or

supplied spare parts that correspond to the

references present in the technical

documentation attached to this manual to

carry out machine maintenance or repair

tasks.

WARNING

Degreasers such as perchloroethylene or

trichloroethylene constitute a health hazard.

Please refer to the product safety file card and

use adequate personal protection equipment

when working with degreasers.

«
...
14
15
16
17
18
...
»

Содержание JC300
































Отзывы:

Нет отзывов