Cutech 40180H-CT Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 35

Cutech 40180H-CT Скачать руководство пользователя страница 22

22

OPERATIONS

NOTE: This operations section was designed to give instructions on the basic operations of this

jointer. However, it is in no way comprehensive of every jointer operation. It is strongly

recommended that you read books, trade magazines, or get formal training to maximize the

potential of your jointer while minimizing the risks.

WARNING! NEVER PASS HANDS DIRECTLY OVER THE CUTTERHEAD.

WARNING! ALWAYS USE CUTTERHEAD GUARD, PUSH BLOCKS, AND KEEP HANDS

AWAY FROM CUTTERHEAD.

STARTING AND STOPPING JOINTER

1. The on/off switch (A) is located on the front of the jointer. To turn the jointer "ON", insert safety

key and move switch (A) upwards.

2. To turn the jointer "OFF", move the switch downwards and remove key. SEE FIG 18.

FIG 18

PLACEMENT OF HANDS DURING FEEDING

At the start of the cut, the left hand holds the work firmly against the infeed table and fence, while

the right hand pushes the work toward the knives. After the cut is underway, the new surface rests

firmly on the outfeed table. The left hand should then be moved to the work on the outfeed table,

at the same time maintaining flat contact with the fence. The right hand presses the work forward,

and before the right hand reaches the cutterhead, it should be moved to the work on the outfeed

table.

«
...
20
21
22
23
24
...
»

Содержание 40180H-CT




































Отзывы:

Нет отзывов