Cutech 40180H-CT Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 35

Cutech 40180H-CT Скачать руководство пользователя страница 20

20

ADJUSTMENTS (cont.)

WARNING!

MAKE CERTAIN THAT THE MACHINE IS DISCONNECTED FROM THE

POWER SOURCE BEFORE ANY ADJUSTMENTS ARE MADE.

INFEED / OUTFEED TABLE ADJUSTMENT

The infeed and outfeed tables are adjustable for coplanar or parallelism if ever necessary. These

are set at the factory. If after planing or edge joining a work piece and adjustment is necessary,

follow these instructions.

1. Lower the infeed table to its lowest setting.

2. Place a straight edge on the outfeed table across the cutterhead and check for parallelism.

3. The straight edge should lay flat on the outfeed table and the cutter tips should just touch

the straight edge on both the front edge and rear of the table near the fence.

4. If the outfeed table is not level (parallel) with the cutterhead, remove and/or loosen the

table screws and washers to access the leveling adjusters. SEE FIG A below.

FIG A.

5. Using a slotted screwdriver, turn adjusters to level outfeed table with cutterhead.

6. Once parallel, replace the washers and screws.

7. Move the straight across the outfeed table, cutterhead, and over the infeed table

8. Raise the infeed table to just touch the straight edge.

9. If adjustment is necessary, use the procedure mentioned above for leveling (coplanar and

parallel) the infeed table.

NOTE: These adjustments, if ever necessary, may take a few tries.

Remove

Adjuster

«
...
18
19
20
21
22
...
»

Содержание 40180H-CT




































Отзывы:

Нет отзывов