Custom Audio Electronics TG1260HIII BP Скачать руководство пользователя страница 92

Страница: 92 / 128

8.3 Cleaning

For periodic cleaning of the device, see the instructions below.

TG1260HIII CUT, TG1260HIII BP, TG1260HIII CUT BP, TG1260HIII CHROMED,
TG2460HIII CHROMED, TG2460HIII TRANSP, TG2460HIII CUT

Platen roller

Paper path

Disconnect the power supply cable and open

the inspection door (see paragraph 5.1).

Disconnect the power supply cable and open

the inspection door (see paragraph 5.1).

Remove any scraps of paper and the

accumulated paper dust in the inspection

compartment and in the paper input area.

Clean the platen roller by using

a non-abrasive cloth moistened with isopropyl.

ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.

Alcohol, solvent

ATTENTION:
Do not use solvents, or hard brushes.
Do not let water or other liquids get inside the device.

ISOPROPYL ALCOHOL

Disconnect the power supply cable and open

the inspection door (see

paragraph 5.1

Disconnect the power supply cable and open

the inspection door (see

paragraph 5.1

Содержание TG1260HIII BP

































































































































Результаты поиска

Содержание TG1260HIII BP

Отзывы:

Похожие инструкции для TG1260HIII BP

Бренды по названию

Популярные бренды

Custom Audio Electronics TG1260HIII BP, Руководство пользователя

Результаты поиска

Содержание TG1260HIII BP

Отзывы:

Похожие инструкции для TG1260HIII BP

Бренды по названию

Популярные бренды