Custom Audio Electronics KPM202 Скачать руководство пользователя страница 47

Страница: 47 / 116

6.3 Printer status

The device operating status is indicated in the coniguration print-out in which, next to the name of the components dis

played, the following information is given:

PRINTER TYPE

device model

Barcode Reader

presence of the barcode reader

RFID module

presence of the RFID reader/writer

PRINTING HEAD TYPE

print head model

INTERFACE

interface present

ETHERNET TYPE

Ethernet connection type

PROGRAM MEMORY TEST

OK appears if functioning and NOT OK if faulty

DYNAMIC RAM TEST

OK appears if functioning and NOT OK if faulty

EEPROM TEST

OK appears if functioning and NOT OK if faulty

PRINTER HEAD Rav

resistance of a dot head

HEAD VOLTAGE

voltage of the head

HEAD TEMPERATURE

temperature of the head

POWER ON COUNTER

number of power-ups made

PAPER PRINTED

centimetres of paper printed

Содержание KPM202





















































































































Результаты поиска

Содержание KPM202

Отзывы:

Custom Audio Electronics KPM202, Руководство пользователя, Страница: 47 / 116

Результаты поиска

Содержание KPM202

Отзывы: