background image

VEHICLE IDENTIFICATION NUMBERS    2

7

2

   VEHICLE IDENTIFICATION NUMBERS

2.1   VEHICLE IDENTIFICATION NUMBER __________________________________________

The Vehicle Identification Number (VIN), consisting of the
model number, date code, and serial number are all
printed on the Nameplate/Identification Decal attached to
the cross member under the dash.

The serial number is also stamped on the cross member.
It is located to the left of the Nameplate/Identification
Decal.

NOTE:

 Reference to the Front, Rear, Left, and Right

sides of the vehicle are always determined by the
operator’s seated position.

Record the Vehicle Identification information below for
easy reference.

Model Number: ______________________

Date Code: _________________________

Serial Number: ______________________

Figure 2A

Always provide the 

Vehicle Identification Number of the

unit when ordering replacement parts or requesting service
information. 

Vehicle Identification Numbers must appear

on all correspondence concerning this vehicle.

2.2

ENGINE IDENTIFICATION NUMBERS _________________________________________

The Truckster is equipped with a Suzuki

®

 three cylinder

gas powered, liquid cooled, four cycle engine.

The Engine Serial Number for the Suzuki engine is
stamped onto the upper engine block on the right side of
the engine, under the engine mount and may be partially
hidden by the electrical harness. The serial number is
also hand printed on the fuel rail.

Record the Engine Serial Number below for easy
reference.

Engine Serial Number: _________________________

Figure 2B

2.3

SDI SPRAYER TANK IDENTIFICATION NUMBERS _______________________________

The model number and serial number for the sprayer
tank is stamped on a name plate located on the front of
the sprayer frame, directly above the fuel tank.

Record the Sprayer Identification information below for
easy reference.

Model Number: _____________________

Serial Number: _____________________

Figure 2C

MODEL
DATE CODE
LABEL #

SERIAL #

84055

CHARLOTTE, NC, USA

1 800 848 1636
Jacobsen.com

M1903

Lb/kg W Batt
Nom Power Hp/kw

75984G55

*

2128855

*

Engine Serial No.

K6A Suzuki

Sprayer Mode l and

Serial No.

Содержание Spraytek DS175





































Отзывы: