Curtiss-Wright DTS1 Скачать руководство пользователя страница 18

Страница: 18 / 140

User Guide

DDOC0099-000-AH

DTS1 CSfC

2 - 4

Overview

Revision 5.0

2.2

Protocols

The DTS1 supported protocols include Telnet, TFTP, CIFS, NFS, FTP, HTTP, DHCP, SNMP, and

iSCSI in addition to its RS-232 console port. The CIFS and NFS protocols are enabled by default,

all others are disabled. The unit also supports SSH, which is always enabled. The user can enable

the desired protocols to support their application. Refer to paragraph 12.3.27

serv

for additional

information.
The FDEEEcPP20 and FDEAAcPP20 Protection Profiles did not consider, nor did they include

networking protocols as part of the security functional requirements, and as a result, did not

include any requirements for addressing those protocols.
Therefore, as per the FDEEEcPP20 and FDEAAcPP20, the protocols have not been examined as

part of the required assurance activities and consequently the evaluation can make no claims

about the DTS1’s networking protocols.
It is suggested that a customer using the product consider the impact of utilizing remote

administration via SSH across the network (rather than through the console) based upon their

specific use case. The customer should factor into their risk management decision the

environment in which the DTS1 operates (dedicated, segregated, private network versus residing

in a Demilitarized Zone [DMZ] accessible to the Internet), and the value of data to be protected.

2.3

CSfC Encryption

Commercial Solutions for Classified (CSfC) encryption is based on a National Security Agency (NSA)

specification. The CSfC program requires multi-layered security. Hardware data encryption is used for

the first security layer. The second security layer is software data encryption. Both encryption processes

are performed in the DTS1, one in the HW crypto module, the other by the Processor. The hardware

encryption key is retained in the DTS1 crypto module memory, the software encryption key is stored on

the RMC module.

2.3.1

Hardware Encryption Layer

CAUTION

DATA LOSS. If the Specific User Token Key is lost, the user account will be rendered unusable.

NOTE

Refer to paragraph 5.3

Hardware Layer Encryption

for information regarding the actual

commands and procedures used to create and log into the hardware encryption layer.

2.3.1.1

Account Creation

Before use, an account must be created (Figure 2.6) on the DTS1 Hardware Encryption (HWE)

layer. To start the account creation, the user logs into the DTS1 via the Command Line Interface

(CLI). Once logged in, additional commands are entered to create an account on the DTS1 HWE

layer. The HWE layer contains a Pre-Shared Key (PSK) which is generated at initial equipment

power-on at the manufacturer and provided separately by Curtiss-Wright. The PSK cannot be read

out of the DTS1. When the account is created, a user token key is internally generated by the

HWE layer. The layer then keywraps the user token key using the PSK and supplies it to the end

user through the CLI. The keywrapped user token key is validated on a third-party system by

comparing the DTS1-generated HMAC and the third-party-generated HMAC. If both match, the

user token is unwrapped using the PSK. The unwrapped user token key is then used in

subsequent logins as the specific-user token.

Содержание DTS1













































































































































Результаты поиска

Содержание DTS1

Отзывы:

Похожие инструкции для DTS1

Бренды по названию

Популярные бренды

Curtiss-Wright DTS1, Руководство пользователя

Результаты поиска

Содержание DTS1

Отзывы:

Похожие инструкции для DTS1

Бренды по названию

Популярные бренды